Random PHH musings...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 30, 2005
Threads
110
Messages
1,028
Location
Secesh
After doing my fourth PHH today I have some thoughts on this item....

The one today came off a SE US truck with 150,000 miles on the clock. It was perfect. No bulging. No deterioration. Nothing. Much the same as I've seen on the other three trucks I've worked on, mine included.

While I do think the PHH obsession is a good thing, I don't feel that it is a DO or DIE event for the average LC that has had decent general maintenance. Like coolant flushes every 30K or so.

Some people on this board buy " heaps " that have no maintenance history. That's where the PHH becomes a critical issue.

I've done my own and three others on nice SE owned 80's. No signs of potential failure in any of them. mine would have passed for almost new at 130K.

My arms are all scratched up and I have decided that there is no good reason to replace the lower pipe bolt when servicing the PHH. Silicone on. Torque clamps good. Top bolt tightened after. No reason for anything more.

Good day to all.
 
Thanks for the info. I just ordered a complete set of hoses for my rig (106k) and have been curious about the condition of the PHH. I guess for the OCD 80 owner replacement of this hose and others can provide some sense of security even if the hose is in good condition visually.
 
Now don't get me wrong. I think it's it's a good idea to replace the PHH with one of these on any 80:

Silicone

I just don't think that it's something that you need to lose sleep over - IF - your 80 is a SE / Western truck - and if it's had some fluid changes.
 
Mine came out in one piece and looked good enough to go another 111,111 miles with ease :)

fzj80oldphh.JPG



But I figured since I was down there doing contacts, I might as well install a new Samco silly hose and be done with it :meh:
 
My LX was reasonably maintained, but I replaced the PHH with a silicone one just to be safe @140K. I noticed the outside of the hose looked good as new, but the inside had cracks. It had spent most of its life in Cincinnati.
 
After stumbling across all the PHH discussions on this board I also got swept up in the paranoia. I was overhauling my cooling system and replaced it then - it was not leaking, but showing some hairline cracks. I'm glad I replaced it for the peace of mind because I would have been really upset if it had blown and left me stranded after I chose not to repalce it.

I would say if you're doiong any work in that area, you should replace it, but not as a dedicated job.
 
I gotta disagree here. This is not a job you want to undertake on the side of the road when it lets go. You can't judge the interior of the hose by the outside condition. I agree with do it right and forget about it for a loong time. This is nothing more than simple preventative maintenance.

Besides, if you do it as a phh ectomie, it is a piece of cake.

Buck
 
When I replaced mine @ about 115K it was weeping on the block side, brittle and cracking. This is on a NE truck. I wouldn't sit on it. If it lets go, you're screwed.
 
Mine had great maintenance. Coolant changes every year which was less than 10,000 miles.

The hose was weeping on the block side because the inside was cracked enough to allow coolant to wick down the nylon strings.

I firmly believe it should be done every 100,000, but silicone hose and constant tension clamps are very optional.
 
there is no need to do a lot of the "required" stuff on a 80 in good upkeep
it is a very well made truck

if not for this board, it would have cost me next to nothing to maintain.

i have come to the conclusion that silicone hose and constant tension clamps are stupid overkill
and i'll not waste my money on that stuff again
cheap, long lasting rubber hoses w/ good old clamps is more than good for OEM and lasted well over a decade, so it's well good for me.
 
The picture below is how my PHH came off at 212K+ miles. If you look close you can see the cracks inside the hose. I didn't replace it until it started leaking because I didn't know what a PHH was or that it existed. It was in my search for info about leaks in the cooling system that i found MUD. And boy, I'm sure glad I did, because the advice & pictures on here really make the difference. I put silicone and constant tension clamps on this time because I don't want there to be a next time. I'm sure that it was an original hose from the hose clamps and how they were installed from the threads on MUD.

I'd also like to add, in the spirit of this thread (Random PHH musings), that I don't think that the damn hose was necessary in the 1st place! They could have come out of the block with that metal tube all the way to where it now ends and started the rubber hoses there. Why in the hell did they need to put a rubber hose at the bottom? The metal tube is bolted to the engine in 2 places so it can't be for vibration flexibility. It is at the top of the tube where flex is needed - NOT the bottom! Any way, - my .02



110_1002.webp
 
Last edited:
there is no need to do a lot of the "required" stuff on a 80 in good upkeep
it is a very well made truck

if not for this board, it would have cost me next to nothing to maintain.

i have come to the conclusion that silicone hose and constant tension clamps are stupid overkill
and i'll not waste my money on that stuff again
cheap, long lasting rubber hoses w/ good old clamps is more than good for OEM and lasted well over a decade, so it's well good for me.


I think that the firewall heater hoses are an overkill gimmick, but I like the PHH to be silicone IF it really holds up longer than rubber. That thing is a PITA and I'm pretty sure I got west nile virus when I changed mine last summer from all of the mosquito bites I got while trying to wrestle the PHH until 3AM. Not only did I have bruised arms, sore back/legs, I also had bone chilling fever and muscle aches that started 2 days after the install.

You can easily see the firewall heater hoses and they take all of 3 miunutes to change if they were leaking. There are a lot more rubber heater hoses on the firewall that take a lot more heat,an wear d time to change than the ones that are offered as a silicone kit.

I wouldn't want to have the PHH blow on me while driving in the middle of nowhere. Git er done and forget about it for a decade.
 
To try and answer 80toylc, if you eliminate the PHH, and replace it with a metal line, you'll transfer the vibrations, twisting, etc. between the engine and the rest of the vehicle, to the line, and eventually, it will crack, leaving you starnded (again, maybe). Toyota would not have installed it if it wasn't necessary! Don't do it!:cheers:Ned
 
To try and answer 80toylc, if you eliminate the PHH, and replace it with a metal line, you'll transfer the vibrations, twisting, etc. between the engine and the rest of the vehicle, to the line, and eventually, it will crack, leaving you starnded (again, maybe). Toyota would not have installed it if it wasn't necessary! Don't do it!:cheers:Ned


Ned, I disagree with you. The metal tube we are talking about is held to the engine firmly by 2 screws - it does not flex nor does it move unless the engine moves. The PHH end only needs to flex when you replace the hose. The top end of the tube, where it connects to the heater valve, which is mounted to the firewall, is where the flex is needed (between engine & firewall). And we do have a necessary hose there. IMHO the PHH hose serves no positive purpose! If the tube was attached to the block, the PHH could have been eliminated.
 


IMHO the PHH hose serves no positive purpose! If the tube was attached to the block, the PHH could have been eliminated.

Which is exactly why i used gates green stripe from the block directly to the heater valve. The metal tubes have been removed. If it ever goes it is a 10 minute fix and the neighbor kids won't hear any yelling and cussing coming from under my truck.

Buck
 
Which is exactly why i used gates green stripe from the block directly to the heater valve. The metal tubes have been removed.

When I did my PHH (a month ago), I was really tempted to do just that. But i just didn't like the idea of that much exposed heater hose taking the brunt of the hottest water in the heater system. And the end that connects to the block is still nasty to get at. Buck, are your 1" spacers a body lift? If so, it prolly helps you get at that end of the hose easier.


If it ever goes it is a 10 minute fix and the neighbor kids won't hear any yelling and cussing coming from under my truck.

Buck


ROTFLMAO - I am with you on that!
 
I can appreciate that.
I used gates green stripe heater hose sleeved inside of a larger gates hose to prevent any chaffing. It has been on for 3.5 to 4 years now and no issues whatsoever. When I did the head gasket, I pulled the gates to inspect it. Looked as good as the day it went on.

The spacers give an adittional bit of lift. These are Mr. Gasket spring spacers. It might make it a bit easier to get to the block outlet. I can use a ratchett on the constant tension clamps which makes it gravy to work on.

Buck
 
Back
Top Bottom