Radio install - not using factory wiring

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 17, 2010
Threads
14
Messages
176
Location
Da UP, eh!
Hi guys and gals

I'm attempting to do a simple install of a new Sony head unit in my 95 LC, not using any stock harnesses or adapters, and completely bypassing all existing equipment. I have removed the factory amp near the glove box, disconnected the amp/sub in the rear. I ran new speaker 14 ga cables to all 4 doors and installed the Pioneer TS-G's (hoping to upgrade later). These will be the only 4 speakers I will be running, for the forseeable future. I'm now on to hooking up the HU. I have a direct battery connection to the yellow HU harness wire, and a ground to the HU harness black wire. Hooked up all 4 new speaker cables to the HU harness. Now...onto my main questions.

Where should I tie in the ACC? Cigarette lighter harness? Other location?
Do I bother trying to tie in the illumination wire anywhere? I guess I don't really care if it dims when I turn the lights on, but would be nice.

I'm going to keep poking away at this, but looking for suggestions. I've installed a radio or two in the past, but it's been close to 20 yrs ago. Thanks.
 
Hi guys and gals

I'm attempting to do a simple install of a new Sony head unit in my 95 LC, not using any stock harnesses or adapters, and completely bypassing all existing equipment. I have removed the factory amp near the glove box, disconnected the amp/sub in the rear. I ran new speaker 14 ga cables to all 4 doors and installed the Pioneer TS-G's (hoping to upgrade later). These will be the only 4 speakers I will be running, for the forseeable future. I'm now on to hooking up the HU. I have a direct battery connection to the yellow HU harness wire, and a ground to the HU harness black wire. Hooked up all 4 new speaker cables to the HU harness. Now...onto my main questions.

Where should I tie in the ACC? Cigarette lighter harness? Other location?
Do I bother trying to tie in the illumination wire anywhere? I guess I don't really care if it dims when I turn the lights on, but would be nice.

I'm going to keep poking away at this, but looking for suggestions. I've installed a radio or two in the past, but it's been close to 20 yrs ago. Thanks.

IF you've left the factor harness in I'd still splice into it for the new HU's power, ground, ACC and dimmer. I don't remember the wire colors, sorry - less chance of engine whine/feedback looped into the new sound system since they were designed for these purposes to begin with.

Also, if ever running a new sub I'd go ahead and run lines to future sub location (RCA, ACC line, etc), hide under carpet and tape ends - much easier now (if carpet/panels still pulled up) and HU still out.

I finished all new system similar approach to yours and have been very pleased with vast improvement over the stock.
 
Yep clock, it dims with the lights.

I get running new speaker wire, I usually do that, but why are you by passing the factory power supply? The adapter to go to an aftermarket head unit is less than $10 and you don't have to cut or splice anything.

Oh....I'm just a wee bit stubborn and when I start on something I usually do everything the way I want...which is 9 times out of 10 incorrect or counter-productive. I didn't cut/remove anything factory, just in-hooked and tucked it out of the way, so I can easily go back.
 
Last edited:
I ended up going back to the harness conversion for the ACC, chassis ground, and dimmer. Gave up on the botch job I had started. Ran the new speaker wires and constant power off of the head unit harness. 45 W RMS x 4 from this HU (Sony WX-GS920BH) to the Pioneer TSG's is pretty impressive for cheap speakers.
 
Last edited:
Back
Top Bottom