Quick 71 buildup thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

rotisserie

don't know if I spelled that correctly .We used some frame machine clamps and scaffold pipe clamps and fashioned a pretty easy to use system for rotating the body.There was alot of structural repair needed in the tub so it was a big help. Being as it is a wheeler I wasn't really trying to make it stock , just strong. I decided to fill the entire dash panel in and drill new holes after we decided what switches to keep.
P1250243.webp
P1250249.webp
PB210073.webp
 
Night before christmas and posting on MUD..............

Ya, Im a cruiser addict also.............

MERRY CHRIISTMAS TO ALL.............................




more to come . gotta go play santa for a bit!

PS , Abels Radd Cruisers new partern, good thing he likes cruises ah........
 
power steering

next came the bearing support for the lower part of the steering shaft.I had to make an aluminium spacer to line the shaft up in the center of the housing.we used a 36" borgeson slip shaft and joints.
P1270279.webp
P1270287.webp
 
seat brackets

Here are a couple of shots of the seat brackets.The passenger seat ended up a little higher than the driver's because of the gas tank.after they were built we sent them off to powdercoat.
P2020299.webp
P2020300.webp
 
paint

well ,here's the color . Originally we wanted a more stock color but My bro wanted endura on the body as well so this is what we came up with. I didn't spray the color myself because a developement company bought the property that my shop was on so I had to move.I moved back into my 400 sqare foot garage to finish up.
IMG_0096.webp
IMG_0099.webp
IMG_0101.webp
 
rhino and hydroboost

We rhinolined the floor before the paint and it seems to be holding up well.we also did the underside of the tub.The next shot is of the hydrobooster I've done this a few times now and I like the way the hydro unit works. This time I did use a stock master though with a wilwood valve on the rear circuit.
IMG_0106.webp
IMG_0145.webp
IMG_0150.webp
 
ram horns

We found some 2-1/2" center dump ram horns and then had to make new wires. We used some big block custom chevy wires which we made ourselves . Next I built the battery tray . It fit nicely in the spot for the original heater .
IMG_0147.webp
IMG_0161.webp
IMG_0158.webp
 
Here is a pic of the mohave heater from flex a lite. It fit nice and had an optional defroster plenum which we purchased and installed .I got the filler cap from a race shop , it installed pretty easily and I dig the way it looks.
IMG_0156.webp
IMG_0166.webp
 
missed a few pics

Here's what it looked like when it was finished.I used an early bib and replaced the two wire sockets on the markers with three wire sockets so they would act as signals as well. We also used later model doors and tail lights . The plan was when we started this build to make a dd /wheeler. It wasn't my intention to keep it stock in any way so I hope it doesn't offend any of you. We had it out for a trail run after we added an aussie locker .It worked great (except for a faulty brake line). I missed a few steps along the way but it was a couple of years ago I think I still have some pics on my old computer . I'll post em' up when I find them.
IMG_0294.webp
IMG_0297.webp
IMG_0299.webp
 
low rear

I just noticed the last pic I posted had the truck sitting a little low in the rear. We had it sucked down with a 2" ratchet to get it out of my garage it sat nicer when it was released.
 
man, i like that filler cap. great way to keep it locked up. which brand fuel door is that?

Shane

Not sure what brand the filler cap is but I think it's fairly generic to the stock car crowd.(that's where I got it) The guys at proformance racing in Maple Ridge B.C. could probably tell you their supplier if you e-mailed them.
 
Kinda looks like this truck...... that was a fun day. Unfortunately thats the extent of the pics of it in action. Not enough time to take pics. To much winching a 4skinner and fixin a spring shackle... :doh:
truck.webp
Wheelin feb 17 005.webp
 
wheeled some crazy s*** today . I thought sliders were for rocks ,apparently if you mount them a 6' 5" they work as tree keeper uppers . I'll try to steal some pics later off black flag but . What a f^2#n' trail . You guys down south should bring the pretty trucks up here and see this s*** . Hard on the paint but what the hell ? Will follow with pics promise ! The guy who cut the trail called it Kawasaki Blood fart take what you will from that . Mike is his name and he rocks a nisssane ,go figure ?
 
Back
Top Bottom