Pre Moab cooling question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 17, 2015
Threads
65
Messages
445
Location
Jefferson City TN
hey guys,

I am currently crashed at a KOA to get a shower and laundry done before we hit Moab for 4 days tomorrow. My 94 80 towed an expo trailer all the way from TN, to flagstaff for overland expo, then to the Grand Canyon and now to Moab. She seems to be doing ok, but I had a concern and wanted to post for peace of mind and or morning fixes.

My trailer is about 750lbs.
Pulling those long grades on 35's and 4.88's had me running with the OD off and about 2500rpms and around 55. Slowed me way down and really lugged the motor. After the climb I noticed a small amount of pink at the tube right above the A/C. It seeped coolant around the hose. Temp stayed good and the rig ran well... Just slow.

Should I be concerned? Every piece of the cooling system is OEM new as of December when I did the head gasket.
 
"right above the A/C'... a/c what? condensor? compressor? evaporator?

If you mean compressor.. there are a couple small tubes.

Need more details.

But, basically.. if you see pink, something is leaking. However if you aren't noticeably losing coolant it probably isn't a very big deal.
 
coolant overflow is full line when truck is warm and about 1" below full line.

No leaking onto the ground and no actual wet coolant. Attached is a pic of what I found.

image.webp
 
leaking hose / the non toyota Worm gear type hose clamp that you are using there have a reputation for damaging hoses when accidentally tightened too much. You may want to replace the clamp with a uniform pressure clamp like an OEM spring clamp, a T bolt clamp or a constant torque clamp. Don't over tighten clamps.

But whats happening is that on these long grades the engine is getting hotter than it usually is. When the coolant starts to get close to 200-212 degrees it begins to build pressure. The OEM cap is designed to purge to the reservoir at 12psi, most aftermarket caps are 13-14psi. So depending on the cap you are using your system can obtain +12-14psi when really hot.

Now when you aren't driving hard up a hill you aren't anywhere near those temps. Mine holds 86 degrees C on the return to radiator line during regular driving, keep in mind that the thermostat begins to open at 82 degrees C. So I am gaining 4 degrees C through the engine. On my hardest climbs (35's, stock 4.10's) I will be floored in 2nd gear and I have never seen more than 94 (201 F) come across my koso gauge. Even then it will expose any leaky lines like what yours did.


You are doing good by selecting OD off. It locks the TC and keeps heat down.
 
I brought OEM Toyota clamps with me and can carefully swap that out tomorrow.
 
Carefully check to see whether that worm-gear clamp tore the hose. Kinda looks like the leak is coming from above the clamp.. but hard to tell. If you need to just cut the end off and push it further on.. should have plenty of extra length for that.

Also note that unless that's the factory rubber hose or something with the exact same diameter and wall thickness the factory spring clamp probably won't be the correct tension on it. They are very sensitive to the overall diameter they are clamping.
 
Pretty much what has been said above. I would add, even when there are no visible leaks, it is possible you have a leak small enough to let air in, this will prevent the system drawing back coolant from the expansion tank. The result is air in the system which we know is not good, so after each hard journey, I am inclined to check levels when cold at the radiator, this is more accurate then the expansion tank.

regards

Dave
 
Carefully check to see whether that worm-gear clamp tore the hose. Kinda looks like the leak is coming from above the clamp.. but hard to tell. If you need to just cut the end off and push it further on.. should have plenty of extra length for that.

Also note that unless that's the factory rubber hose or something with the exact same diameter and wall thickness the factory spring clamp probably won't be the correct tension on it. They are very sensitive to the overall diameter they are clamping.
exactly why i like t-bolt clamps
 
Back
Top Bottom