power stering coolier

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 23, 2005
Threads
74
Messages
1,267
Location
Ivydale W.V.
power steering coolier

As I'm getting my 80 ready for CMCC I would like to add a tranny coolier to the power steering.
Where is the best place to put it, I think the coolier that is on there stock is just a line that runs down behind the front bumper, is it low persure, can I cut them and add the tranny coolier there.
Whats your input, thanks


Tim
94 fzj 80
tlca #14863
Prez. Mountaineer Cruisers
 
Last edited:
To answer your question yes. Remove the Toyota paperclip and slap in a new cooler. There are a few threads on how to do it.
 
Thank you, I did a search and found nothing, I will try again.

Tim
94 fzj 80
tlca #14863
Prez. Mountaineer Cruisers

see my sign .. I end using my tranny cooler as PS cooler after my tranny swap . ..
 
i got a trans cooler (i think from summit) and picked roughly the right dimensions for the space in front of the radiator. it works well and was cheap.

My friend got a cylinder style of cooler that is more low profile and fits at the lower crossmember below the radiator. I think that's cleaner but don't know if it cools as well.
I may do that if I need the space in front of the radiator for a electric fan.
 
I have a small PS cooler in front of the tranny cooler. It's about 3" wide x 6" long and the oem cooler is still in service. I like the idea of having additional fluid capacity as well as additional cooling so the oem unit was kept. This works well for me.
 
Here is the one I run for my steering, but you could just as easily use it for the tranny.
CIMG0010.webp
 
Here is the one I run for my steering, but you could just as easily use it for the tranny.

Wouldn't your bumper restrict air flow to that cooler??
 
My intention is to go Hydraulic winch so to help things out this is the cooler I have:
13260-angle-large.jpg

Heat Sink Coolers

And here is the cooler/filter/reservoir I have to replace the stock Toyota one using Aeroquip fittings (I found the Toyota filter equivalent):
fittings2.webp
fittings.webp
 
that's the one my friend got nlxtacy. i think the single pass. how much was it?

why an engine oil cooler? that is not needed at all, imo.
 
The reservoir was from Appleton and was about $150.

The Delare cooler is to replace the stock Toyota paperclip power steering cooler. That was like $60
 
The reservoir was from Appleton and was about $150.

The Delare cooler is to replace the stock Toyota paperclip power steering cooler. That was like $60
\


I was looking at my PS reservoir and this one and it seems like you would need to cut a hole in the hood for that one to fit :confused:
 
I was looking at my PS reservoir and this one and it seems like you would need to cut a hole in the hood for that one to fit :confused:

Thats what a custom bracket is for. I bought a used reservoir so that I could take off the bracket and have a new one made and welded to the fins so that I can drop the reservoir height down. There is plenty of room below.
 
Interesting, I never really thought our PS really needed a cooler, but I am gonna look into it a little more! I like that low profile one NLXTACY
 
Interesting, I never really thought our PS really needed a cooler, but I am gonna look into it a little more! I like that low profile one NLXTACY

Well our trucks need one because they have one already built in. All we are doing is replacing the stock paperclip design with a finned design or radiator design. For me, I was trying to figure out how I could incorporate a P/S filter. I wanted cooler/cleaner hydraulic fluid to make sure my newly replaced power steering pump will last forever. When I found the filtered reservoir it became an easy decision. I just have to get it all hooked up. :hillbilly:
 
Back
Top Bottom