Possible hg troubles :(

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 27, 2016
Threads
1
Messages
8
Location
Winchelsea, VIC, AU
I want to start off by saying hello! I'm new to the forum and have a question about a 97 land cruiser 4.5 petrol I'm looking to buy from my boss so I have a much needed second vehicle. The land cruiser may need a hg but it may also be the head. I'm here to pic your brains and see what you all think. So fist off it has 359,000+ km on it with original head and gasket. My boss is meticulous about maintenance so I know it's taken care of but he was helping his daughter move a few weeks ago and blew the radiator. His mechanic said it built up pressure instead of overheating which would normally be what happens. Water is getting into the oil causing a milkshake colour. Runs fine but starts getting sluggish after about 15 minutes of driving. And check engine light comes on. Any help would be greatly appreciated!!
 
If coolant is getting into the oil, the head has to come off. Coolant in the oil can destroy bearings. Try not to drive it till its fixed.
 
i know not to drive it and I know the head has to come off but if I can get the necessary parts to fix it before it gets to my house it would save a great deal of time which is why I posted here. I'm only buying it because I'm getting a good deal on it and I know the quality of Toyota. So, is it the head or the gasket?
 
take the head to a machine shop and have it checked/ rebuilt. also a good time to doall of the "while u are in there stuff". mainly cooling system related but also injectors etc.

read read read - headgasket threads and you can make yourself a list of what to order so you have it all.

if rust is an issue- i personally would delete the rear heater/ terminate it at the firewall. nothing like redoing a head/ hg and then finding out that a rear heater line is slowly leaking onto your exhaust - going completely unnoticed until you cook/ overheat/ warp your new stuff.
 
There's no way to know what the problem is until the head comes off and is checked for cracks.

The correct course of action is to remove the head and take it to a machine shop. They'll check the deck and manifold surfaces for flatness and machine it if necessary. They'll also check to see if it's cracked. A cracked head can cause coolant to get in the oil too.

Cracks in heads are caused by overheating. But overheating will not necessarily crack a head.

The machine shop is going to need the head for several days at least. Plenty of time for you to order parts. The head will probably need some new parts anyway. Oil seals etc.

This won't be a weekend job.
 
As I am an ASE certified technician I am aware that this is not a week end job. The book time is 12 hours and the reason I was here is to see if the most common problem for this engine (since I have never owned a Toyota here in Australia as I'm from the states) was a head or the gasket so all I really needed to know was if I needed to order a head...yes I do, and now I will order the parts so I can dig into it when the vehicle arrives. Thanks for all the quick replies!
 
Fairly rare to replace a head unless it has seriously overheated. You did say it get hot, check with your boss and see if he shut it down immediately. Almost certain it would have to be resurfaced.

I overheated mine twice before a rebuild, head was fine but then again, I shut it down pretty quick and, in one case, stopped next to a snow bank and cooled her off pretty quick.

If you are concerned, find a used head and have it rebuilt and ready when you pull her apart. The next question will be how the block and cylinders look once you pull the head.

Good luck!
 
It did not get hot, the pressure from the exhaust getting into the cooling system was what blew the radiator and he shut it down straight away and had it towed to his mechanic. Thanks for the info Azca
 
Cracked heads on the 1fzfe are rare. Head gasket failure is much more common. Occasionally heads are warped too much to be milled back to spec , but not often. You can't tell for sure til you have it checked out. I would LOCATE the parts and service that you MAY need first, then BUY as needed after the head is off .
 
So here's an update on the head issue.
I pulled the head off an found the cam had rubbed the #5&6 cam lobes on the exhaust side. I got a rebuilt head and all is well except it idles high (1200-1500) moved distributor 1 tooth and barely runs.
What can I check to fix the high idle? I sold all of my tools when I left the states and moved to Australia otherwise I wouldn't have to ask silly questions. Anyone else have similar issue after head install. Timing marks are all perfect btw
 
Throttle cables not adjusted right, cable should be somewhat loose not tight
 
Back
Top Bottom