Ordered MV4500 for Cruiser

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 19, 2006
Threads
126
Messages
773
Greetings once again.

After today, I promise I'll strat posting pics for my restor-mod to stop teasing you guys.

Well the tear down is going well so far got all the interior out and the front clip off. There is very slight surface rust near the heater core hoses on the passenger floor pan. In addition in almost the very same place there is surface rust on the drivers floor. The soda blaster inspected the floors and indicated that it the rust hasn't penentrated lower than surface so it should be okay.

Next we'll be taking out the existing 350 for a rebuild. I decided rather than use the stock 3 speed transmission I would upgrade to the 5 speed NV4500. Yesterday I ordered the transmission (dodge) with the necessary adapters from Advanced Adapters. I hope the transmission fits with very little modifications, but chances are I'm going to have to do some major welding (thank god for friends).

Since I'll be tearing into the transmission I also ordered the rebuild kit for the transfer case. Accroding to Advance Adapters the transfer case should be able to handle the 350 and the new 5 speed.

Please provide me with your opinions on using the stock transfer case with the NV4500 and 350.

Next on the list for restoration is the following:
  • Soda blast
  • Body Work
  • Paint
  • Lift
  • Wheels & Tires
My last question for you guys is the following: How does one remove the hard top? I taken out every bolt and the thing won't budge. It's a real PITA. Suggestions are appreciated.

:cheers:
 
Last edited:
there is a bolt inside the door jam area (inside the vehicle) about door striker level ,that may be tight , holding the hard top from coming off , loosen the bolt ,
IMG_0542 (Small).webp
 
Actually my budget is $10,000 for the entire mod-restoration. The transmission was the most expensive setting me back about $3,800 with all the adapters. I think I can accomplish the remainer with the remainder of the buget (outside the the engine rebuild).

The soda blast with sealer is $750
Paint estimated at $2,500
Body Work $1,500
Wheels & Tires $1,000
Lift $1,100

I'm thinking I can get major money for the Cruiser when its fininshed. There is a huge interest in older mod-resotred land cruisers becasue of the lanch of the toyota's latest and greatest.

BTW the cruiser already has power stearing, so that alone save me a bunch.


PabloCruise said:
I bet that runs some $$$
 
Last edited:
UNO_RACING said:
I'm thinking I can get major money for the Cruiser when its fininshed. There is a huge interest in older mod-resotred land cruisers becasue of the lanch of the toyota's latest and greatest.

This statement seems to be at odds with what most folks around here report about modifying and then selling their cruisers. Do it for yourself but don't expect to get all the dollars out of it for your investment in parts (or by any means for your time).
 
UNO_RACING said:
I'm thinking I can get major money for the Cruiser when its fininshed.



You might be able to, but that has really been the exception instead of the rule when it comes to this type of vehicle.


Good luck!


-Steve
 
UNO_RACING said:
I'm thinking I can get major money for the Cruiser when its fininshed. There is a huge interest in older mod-resotred land cruisers becasue of the lanch of the toyota's latest and greatest.


I'm thinking you have much to learn, but good luck with the project. A restored stock Cruiser might be worth something, but major mods like you plan will likely net about 50 cents on the dollar. What are you doing for a transfer case?
 
Cruiserdrew said:
I'm thinking you have much to learn, but good luck with the project. A restored stock Cruiser might be worth something, but major mods like you plan will likely net about 50 cents on the dollar. What are you doing for a transfer case?

You're absolutly right...I do have a lot to learn, but that's part of the process and why I'm here. Chances are that I won't sell it, but I like to keep all my options open.

Incidentally, in 2002 a friend of a friend of mine restored a old bronco and modded the hell out of it. It actually appeared in SEMA, sponsored by Rino Liner. He put about $15K into it and sold it for $49K. Perhaps it was becasue it appeared in SEMA, maybe not---but any price is possible to the right buyer.

Lastly, I'll be using the stock transfer case, but it will be rebuilt from a kit provided by Advanced adapters. Does anyone have suggestions for a transfer case?

I'm going blind here so your opinions are valuable to me.
 
BTW the cruiser already has power stearing, so that alone save me a bunch.

Factory or somebody did a Saginaw conversion? What year is your Cruiser?

Lastly, I'll be using the stock transfer case, but it will be rebuilt from a kit provided by Advanced adapters. Does anyone have suggestions for a transfer case?

Huh? If I were using a 350/ NV4500/ stock tcase a brace would be mandatory, such as a Pardi tcase stiffener plate. From your description, this is gonna be a turn key project, so no trail duty?
 
pbgbottle said:
there is a bolt inside the door jam area (inside the vehicle) about door striker level ,that may be tight , holding the hard top from coming off , loosen the bolt ,

So that is what that bolt is for. Does that help w/rattles, have to try that next winter. Thanks.
 
LC_Hamma said:
BTW the cruiser already has power stearing, so that alone save me a bunch.

Factory or somebody did a Saginaw conversion? What year is your Cruiser?

Lastly, I'll be using the stock transfer case, but it will be rebuilt from a kit provided by Advanced adapters. Does anyone have suggestions for a transfer case?

Huh? If I were using a 350/ NV4500/ stock tcase a brace would be mandatory, such as a Pardi tcase stiffener plate. From your description, this is gonna be a turn key project, so no trail duty?

The power stearing was actually completed in the 80s. The previous onwer used a conversion kit from Advanced Adapeters and a stearing colum, pump and hardware out of a Monte Carlo. As part of the conversion the 10" of the front frame rail was cut and in its place 1/4 steal plates were welded. I've talked to other land cruiser folks and appaently this was standard practice.

I haven't decided if it will get trial duty. I have a couple of friends that are rock crawlers, so chances are that it just might get trial duty. Right now I'm just in limbo.

In terms of the brace it is provided in the kit from Advanced Adapters.
 
Back
Top Bottom