OME Dealers

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 6, 2005
Threads
56
Messages
214
Location
Bellville, TX
Are there any dudes on Mud that sell OME products? I need some caster correction bushings.

I'd like to support one of our sponsors if possible, but would like someone who's likely to have these in stock so I don't have to wait long to install.

The closer to Houston the better!

:cheers:
 
I have the same lift as you (OME 850/860) and I would go with Slee's caster correction bushings instead of the OME's. The Slee's have a better chance of getting you into spec (2-4 degrees) as they give you 3 degrees of correction instead of the 2 degrees provided by the OME's.
 
Top of the page, there is a tab that says "Vendor Market", slick on it, then go to "Vendor List". You will find all the forum sponsors, most of 'em will carry OME. Cruiser Outfitters and Slee both have good reputations, among others...
 
I have the same lift as you (OME 850/860) and I would go with Slee's caster correction bushings instead of the OME's. The Slee's have a better chance of getting you into spec (2-4 degrees) as they give you 3 degrees of correction instead of the 2 degrees provided by the OME's.

x2 for Slee's, its what I used.
 
Kurt of Cruiser Outfitters (Utah) is 5-star. Total class, unbeatable prices.
Cruiser Outfitters

I agree with Tofo, you really can't beat his prices and Kurt is a stand up guy to work with. He just pressed in some bushings for me recently.
 
What's a good price range to expect to have shop press out my OEM bushings and press in my caster correction bushings?
 
What's a good price range to expect to have shop press out my OEM bushings and press in my caster correction bushings?

I don't know good, but my shop (brake alignment specific shop) said standard hourly rate of $60/hr. and est 4hrs.

A kick @$$ local mudder/chapter guy had a 12ton press and offered up to to help install mine. Still took 3hrs. One side gave a bit of trouble removing, the 2nd side took no time at all.
 
A local shop here said he could do it with his 50 ton press, but that they can STILL be a hassle. He (and most around here) are way higher than $60/hr.

But then again, what am I gonna do? If I can't do it with a BFH or holler at them to get out, I'll pay the guy and like it! ;)
 
A BFH will not even touch it. The 12ton worked fine, it was the press tool we had to improvise making it harder. A 20ton with a press tool would be cake walk.
 
FWIW I'm $150 on the truck, $50 off of the truck. Takes about 2 hours start to finish on the truck, 45 minutes off the truck.

I've heard as cheap as a '6-pack' at the corner auto-shop and as much as $400 for the caster correction install.
 
Kick @$$ Kurt. :D

EDIT: Tech question, if removing both off the truck leaving the front rotate (to my knowledge and input) to ship or drop off to a shop how do you keep things in line for re-install. (sorry if its a lame half :banana: question)
 
Kick @$$ Kurt. :D

EDIT: Tech question, if removing both off the truck leaving the front rotate (to my knowledge and input) to ship or drop off to a shop how do you keep things in line for re-install. (sorry if its a lame half :banana: question)

Are you asking how do you keep your axle from shifting if you take the arms off to press in bushings?

If so, then most people just use some ratchet straps to secure it to the frame. It's probably a good idea to put some jack stands under the frame just in case it wants to shift on you. I strapped between the coil mount and the knuckle and then midway back to a hole in the frame.

Between ratchet straps (front to back alignment) and a floor jack (vertical alignment) it was very easy to get the arms w/ new caster bushings to line up to the axle and frame. Most of that can be attributed to Kurt's good bushing press skills and measurements. If they aren't installed within the correct tolerances it can be difficult for the holes to line up.

Kurt definitely has the best service and lowest price that I've seen. For some of the prices I've seen quoted, it would probably be cheaper to pay to ship him the control arms if you aren't local. :cheers:
 
Dead on Nick. Thanks. I did not jack either side up, but did one at a time using a ratchet strap to secure the position. Makes sense.
 
FWIW I'm $150 on the truck, $50 off of the truck. Takes about 2 hours start to finish on the truck, 45 minutes off the truck.

I've heard as cheap as a '6-pack' at the corner auto-shop and as much as $400 for the caster correction install.

Thanks, Kurt, for that. Great reference point.

:cheers:
 
$50 off of the truck

That's a great price! :eek: I removed mine myself and had a local Firestone press them with LandTanks template and they charged $75.
 
That's a great price! :eek: I removed mine myself and had a local Firestone press them with LandTanks template and they charged $75.

$75 is fair for a shop that probably that isn't right ready to do them. I've got a press always set up for them with a template for the OME bushings that makes for a quick and painless install. Worst case I have a spare set of arms I use as a 'core' for local installs, I use them when I do installs or send them home with customers who are doing an install shortly, that way they can just pull theirs off, replace them with my donor arm with pre-pressed bushings and return their cores to me. I clean them up, make sure the top bushing is clean and press in the OME bushes again when I have a set or two to do. A round and round circus :D
 
Back
Top Bottom