Occam's Razor

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 14, 2018
Threads
12
Messages
398
Location
Silverthorne, CO
Driving into work today my throttle felt a little sticky. My cable jacket is torn up so a replacement was on the to do list anyways. No big deal....

Pulling up to a 4 way stop I suddenly had no power brakes and the tac was still sitting at 3k even though I was off the throttle. I had to lay on the brakes to stop and thankfully was only one turn away from the office parking lot, so I made it into a space and stopped.

My first thought was some major drivetrain issue (just replaced my trans so I was not too excited). Went inside, had some coffee, and came back out to reassess the situation with a clear head, starting with the most obvious solution.

As you can see from the photo. The little rubber stopper on the throttle cable had jumped around and was causing the problem by preventing the throttle body from returning to "idle".

This was a good reminder of the most important aspect of diagnosis. Check the simple things first!

20200114_113323.jpg
 
There were no power brakes because the throttle wasn't closed and therefore the engine had no vacuum
That's not quite accurate, a very important part of any power brake system is the power brake vacuum reservoir that most master cylinder bolt to. That system has a one way valve on it that allow vacuum to be accumulated in the reservoir. One of the main safety reasons why vacuum is accumulated in the reservoir, is to allow the operator to still have power assisted brakes* in the event the engine should quit running. *In the event of engine lost, you'll still be able to push the brake peddel 2, or 3 times before all power assist/vacuum is exhausted.
 
That's not quite accurate, a very important part of any power brake system is the power brake vacuum reservoir that most master cylinder bolt to. That system has a one way valve on it that allow vacuum to be accumulated in the reservoir. One of the main safety reasons why vacuum is accumulated in the reservoir, is to allow the operator to still have power assisted brakes* in the event the engine should quit running. *In the event of engine lost, you'll still be able to push the brake peddel 2, or 3 times before all power assist/vacuum is exhausted.

Yes, and why turbo vehicles also have working power brakes.
 
There is a significant reduction in brake vacuum with the engine above idle. Combine that with the fact that you're still accelerating, fighting the brakes, and you have far less overall braking.
Try driving around sometime with the hand throttle set.
 
I was just assuming that was the OP's issue with their brakes. I am familiar with the reserve of vacuum a braking system has, but if the throttle was not shutting all the way he would lose all vacuum assist after a few stops. It's possible that the OP was driving to work and didn't notice the idle was above normal for a few stops and only noticed when there was no vacuum assist. That was my guess above.
 
I was just assuming that was the OP's issue with their brakes. I am familiar with the reserve of vacuum a braking system has, but if the throttle was not shutting all the way he would lose all vacuum assist after a few stops. It's possible that the OP was driving to work and didn't notice the idle was above normal for a few stops and only noticed when there was no vacuum assist. That was my guess above.

You are correct. That is exactly what happened. Not sure when the stopper got jammed up with the TB. If I remember correctly I only hit one stop on the way to work that morning. My commute is rather uphill so I am usually higher in the rev band for most of the drive which is probably why I did not notice the issue until the stop.

To be clear the 80 did come to a full stop, but I was standing on the brakes with the throttle still open.
 
I was just assuming that was the OP's issue with their brakes. I am familiar with the reserve of vacuum a braking system has, but if the throttle was not shutting all the way he would lose all vacuum assist after a few stops. It's possible that the OP was driving to work and didn't notice the idle was above normal for a few stops and only noticed when there was no vacuum assist. That was my guess above.
When the throttle on an engine is slammed fully open to WOT (wide open throttle) vacuum will drop off to zero, or near zero briefly, and then begin to recover. Even if@KC masterpiece had the throttle half way open while driving the whole way to work, if his engine is in good mechanical condition, it should be producing at least 10 inches of vacuum. That's more then enough vacuum to keep the vacuum reservoir fully topped off even after repeated use of his brakes.

In the 5 years I've been a member of Mud, I've read more then a few threads about our 20 plus year old trucks power brake boosters failing. So if he is in fact having an issue with the lost of his power brakes. I'd start by testing the power brake booster, and vacuum check valve first, as a possible cause. Cheers
 
When the throttle on an engine is slammed fully open to WOT (wide open throttle) vacuum will drop off to zero, or near zero briefly, and then begin to recover. Even if@KC masterpiece had the throttle half way open while driving the whole way to work, if his engine is in good mechanical condition, it should be producing at least 10 inches of vacuum. That's more then enough vacuum to keep the vacuum reservoir fully topped off even after repeated use of his brakes.

In the 5 years I've been a member of Mud, I've read more then a few threads about our 20 plus year old trucks power brake boosters failing. So if he is in fact having an issue with the lost of his power brakes. I'd start by testing the power brake booster, and vacuum check valve first, as a possible cause. Cheers

Engine is in good shape. Never had any issues with the brakes prior to this. A fluid exchange is on the list for spring and I will take a look at the brake booster. I did replace the brake booster lines this past summer, but didnt touch the booster itself.
 
It's hilarious that a thread about keeping it simple became so complex.
 
One thing that may be hurting your trucks brakes, is the fact you live in CO. Living there your at a much higher elevation, and as you go up in elevation the ability of the engine to produce vacuum will be diminished. So if your booster is getting weak, coupled with your elevation, it may become more of a problem.
 
I'm no expert, but maybe the truck was difficult to stop because it was running at THREE THOUSAND RPM'S?
 
I was waiting for someone to consider that.

Yes it was still in drive at around 3k. Like I said I will check the booster as a "while I'm in there" project.

Waiting for someone to suggest it's a failed HG.......
 
You should probably check the muffler as well, as I'm sure it was louder than it usually is.
 
Back
Top Bottom