OBD1 to OBD2

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 20, 2013
Threads
46
Messages
1,073
Location
PA
Background. I picked up a '93 "parts truck" a couple months back with 264,000 miles. After looking it over, it is in much better shape than the '95 I have been driving for the last six years. I've been driving the '93 somewhat regularly to shake out any quirks it might have. Two have shown up, one being a 400 rpm idle when semi warm, and the transmission occasionally not shifting into gear.

Doing some digging on the forum, the trans issue is probably solenoids. The idle issue doesn't seem to have a clear origin.

After driving the '95 for the past six years, it is noticeable that the OBD2 is more refined than the OBD1 setup.

I am going to pull the drivetrain in the '93 this spring to reseal the engine, replace all the coolant hoses, etc. It is leaking oil pretty severely, but it doesn't burn a drop. I also have transfer case gears that will be installed, and the CDL actuator to repair. By that time the '95 drivetrain will be out of the truck.

So what I am considering it converting the '93 to OBD2. Ordinarily this would be a silly idea. But since I have the '95 sitting here, all the parts are available to me.

I'm interested in the collective's input on this one...
 
I could be mistaken, but i think i read here on Mud that the OBD2 system uses more sensors on the engine, and possibly the trans*, then the OBD1 system does. So before you start this swap you might want to make sure that the older OBD1 engine and trans has all the threaded holes/locations on them for all your new OBD2 sensors to screw in to.

Along with all the OBD2 sensors you'll need to swap over, You'll also have to swap over the main engine bay wiring harness that connects all those sensors to the engine, along with the harness that's up under the dash that connects to the OBD2 ECM.

On top of the items I've listed that'll need to be changed, I'm sure there are other items I've missed. Just a suggestion, but when you do this swap you should start a thread here on Mud. Take lots of photos while your doing it, so that way you'll be able to help the next member who might want to do the same swap.

*Don't forget the trans used on the 93 (bus trans) is different from the one used on the 95.
 
For the 93 (I have the similar only 94). I chased 200-400 RPM idle for about 2 years. Checked for leaks using smoke, propane, carb cleaner and vacuum gauge. No leaks found but I still replaced all hoses. An unrelated system variable fixed the idle for me: the PS pump. I had a badly leaking PS pump. I rebuilt mine, replaced all hoses and noticed immediately my idle became steady and is up to 675 or so. I can only report based off observations and not why they are related. A buddy of mine brought up a good point, inefficient pump placed drag on the motor. Second issue, the transmission. Are you experiencing any secondary or tertiary symptoms? The A442F trans locates the Neutral Safety Switch on the driver side and the cable connector to the TCU sits right under the PHH. This is subject to corrosion. I am very familiar with this because it happened to me. When I disconnected the connector,, the female connectors on the TCU side literally disintegrated into a green powder. As soon as I fixed it, PRND2L dash light came back, reverse shifted instantly, the car started off in first as it should and reverse lights came back. Also, and perhaps more importantly, I achecived full lockup and could cruise at 65 doing 2200 RPM again. Wit the NSS issue, I would do over 3500K at 65 MPH
 
I could be mistaken, but i think i read here on Mud that the OBD2 system uses more sensors on the engine, and possibly the trans*, then the OBD1 system does. So before you start this swap you might want to make sure that the older OBD1 engine and trans has all the threaded holes/locations on them for all your new OBD2 sensors to screw in to.

Along with all the OBD2 sensors you'll need to swap over, You'll also have to swap over the main engine bay wiring harness that connects all those sensors to the engine, along with the harness that's up under the dash that connects to the OBD2 ECM.

On top of the items I've listed that'll need to be changed, I'm sure there are other items I've missed. Just a suggestion, but when you do this swap you should start a thread here on Mud. Take lots of photos while your doing it, so that way you'll be able to help the next member who might want to do the same swap.

*Don't forget the trans used on the 93 (bus trans) is different from the one used on the 95.
True about the A442F, its rare for the bus trans to go out. I posted a possible fix.
 
You would need to swap the engine and transmission plus all the wiring behind the dash and th dash itself.
 
So bringing this back up. My '95 is down to the chassis, the transfer case is out, and the engine and trans are chained to the hoist, ready to be pulled this weekend. I have pulled all of the wiring harnesses, and every component from the '95.

The trans issues with the '93 have become more frequent since the weather warmed up, and the idle issue is still there. So I am going to move ahead with this project.

I'll be keeping the '93 engine, using the '95 trans and transfer case (swapping in 3.1/1 lr gears).

What I know/think I will have to do:
- Swap oil pans and crank signal ring onto '93 engine.
- Swap '95 EGR controls (may just swap entire intake manifold)
- Swap engine/trans wiring harness(es)
- Swap '95 exhaust manifolds (removing pair system)
- Swap '95 air cleaner (lid at a minimum)
- Swap '95 exhaust system

What I do not know:
- How far down the chain of wiring harnesses I will have to swap. May have to swap them all.
- Will I have to swap the steering column.
- Is there any difference in the fuel system, ie fuel pump, wiring, plumbing, etc. The fuel system plumbing in the '95 was on the verge of failure due to rust.
- I am sure there is more...

If you think I am crazy, I cannot argue with you :) I wouldn't consider this if I didn't have all the parts on hand. But I am also innately curious, and am very curious to see what the differences are.
 
I've owned the '95 truck for six years. Rust took its toll, so I've parted it.
 
Back
Top Bottom