New and Blue Rig

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 28, 2004
Threads
70
Messages
285
Location
Orlando, Fl
my friend just bought a 72 fj40, and so heres a pic.... and um, now for the questions (it doesnt run for very long) while it did run, the transfercase would not go into 2High, only 4 high and 4 low.. what should i do? any seggestions, and the carb needs to be rebuilt, its a 2 barrel, where should i get a kit for it... and why do i need to put my hand over the carb to get it to start?
 
That color combo is sweeeeet! :D As far as the carb kit if you know what your doin liquid offroad had the best prices on the oem type rebuild "keisler brand???" kit that is supposed to be the better kit or you could go with any of the kits from autozone etc that have directions. I went with the oem and my mechically inclined bud backed out and now im left starin at a bunch of itsy bitsy chit that all goes somewhere. :rolleyes:
 
Nice Cruiser. The carb needs to have a working choke on it. When you put your hand over it, that does the same a choke. A carb kit you can get from many places like Man-it-aint-free or Man-a-fre even. SOR also. The 2/4 wheel drive lever portion is seperate from the High/low lever where it goes into the transfer case. One is a push pull into it, the other goes into a pivot that changes it to a left/right movement. I would check those bushing and connections first to see if one of them isn't moving the way it is supose to.

TC
 
I just had this problem after the fuel gauge quit and my 40 ran out of gas a couple of times, I checked both fuel filters and they looked new and clean (check his filters) fuel pump is relitively new. It did not seem to have a lot of fuel coming to the setiment bowl so I blew some air up that line and boy did it come out after that, It must have had some restriction in the tank. It seems to have better top end now and I do not have restart it in the mornings anymore.
 
don't think i like the red, but a good starter...as for the t case, pull the top cover and check the fork for proper alignment to the collar and make sure they're not both worn out.
 
I don't believe it is the shifter fork that is for high and low 4wd. Sounds like it is working. If I'm correct it sounds like the 2wd 4wd engagement shaft. Should be easy to inspect. It is the shaft on the case with a roller attached to the shifter. Make sure it's not bound. If it move freely then you have internal problems. Truthfully I'd drain it pulloff the front output shaft housing and inspect. But will need a gasket if you do. But you may get lucky by lubing the shift shaft and don't forget the zert on the shaft comming out of the trans that hold the shifter it need to be greased.

Also forgot try putting the clutch in when going from 4wd to 2wd. Could be your problem.
 
Did cha lock the hubs? Is there a front driveshaft?
 
good news, the transfer case went into 2High, and it drove fine, i think it might have been stiff,(not being used in 3 years) so thats all fine and dandy, we got working on the carb today, cleaned it out (lots of sut* sp?) and it will now idle. flushed out rad. all kinds of junk floated out of it, lots of mold, we used a rad flush and it worked well. next: we snapped the accel. cable driving it down the street, so i was wondering if i can get a new one from a local store, or will i have to order one?

Jonathan/SandRider - Ryan/BigBlue
 
Thats my CRUSIER!! YeAHH! anyways..my user name is newrider..i should have made it blue rider...but you know..maybe later.......thanx for all you guys help! much appreciated
 
Back
Top Bottom