Need help advise ASAP!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 30, 2009
Threads
133
Messages
3,210
hey guys,

Wandering if anybody can advise me.

My front driveshaft u joint failed on the interstate yesterday.

I trailered the lx450 home but need help with the driveshaft repair.

The front flange that connects the drive shaft to the transfer case is completely destroyed. The drive shaft where the universal joint goes got pretty damaged and there is a dent further down where the drive shaft whipped around and banged on the crossmember.


What is the easiest fix?
Where do you recommend I get a new driveshaft and flange?
Any help and advise is greatly appreciated since I need to get o work for the next few days before I go on vacation.

Pictures for reference will follow.
 
Weird.... Would a U joint failure cause that flange to rip apart like that? It's almost as if the transfer case suddenly stopped and the driveshaft ripped away from it.
 
If the driveshaft is damaged, it wont be a quick fix as i wouldnt trust it to drive highway speeds. You can always hit the wreckers to see if there is one. Toyota will be pricey, but may have them in stock. If it were my rig, id contact a third party driveshaft company and get one made.

Flanges and ujoints can be replaced easy peasy, even ordered from rockauto, its the drive shaft damage that worries me
 
My wife was driving it. It is entirely possible that the universal joint had failed 6 hours prior to it completely failing. My wife told me that the whole truck had been shaking real bad. Of course she said this after driving at Highway speeds for 6 hours. I removed the shaft and inspected everything else and cannot find signs of any damage.

I am currently looking at the classifieds for a replacement driveshaft. Unfortunately I don't trust anybody near me to touch my truck. I'm no mechanic and still trust that I can do a hell of a lot better job than any shop near me. Been burned too many times around here.
 
Easiest fix? How about the easiest band-aid to get you to and from work.
Do you have a CDL switch? If so, completely remove the front driveshaft, lock center diff and drive all you want while getting the front shaft fixed.
If you dont have a CDL switch, you can use your hazard switch (after trimming a plug alignment tab on the back of the switch). The wiring harness is already existing, behind the radio bezel.

I'll see if I can dig up the threads with the DIY instructions.

This give you plenty of time to get what you need to properly fix your drive shaft and find the best priced parts.

*Forgot to mention, if you use the hazard switch for the CDL, your turn signals won't work becuase the switch is no longer plugged into the hazard harness.... buying a second hazard switch or actual CDL switch will allow both CDL and turn signals to work at the same time
 
My wife was driving it. It is entirely possible that the universal joint had failed 6 hours prior to it completely failing. My wife told me that the whole truck had been shaking real bad. Of course she said this after driving at Highway speeds for 6 hours.

My ex wife had a similar attitude toward cars.... "Steam was coming out of the hood - but after a while it stopped doing that so I kept going"... Head gasket on an 83 peugeot - more than the car was worth... Thankfully I've put the fear of God in the current wife and the kids.. 'IF SOMETHING DOESN'T SOUND RIGHT - STOP AND CALL ME AND I'LL TELL YOU WHAT TO DO'
 
Just thought I would mention that if you go aftermarket I highly recommend Tom Wood's www.4xshaft.com. I have used them twice in the past and was impressed each time with the level of service and finished product.
 
I installed the cdl switch a while back. The driveshaft is out. I fiund a couple driveshafts on the Internet on mud classifieds. Waiting on folks to get back to me.

So CDL switch on, And no drive shaft, and I can drive the truck with no issues?

I will drive it around the neighborhood first. Before I decide to take it on the road.
 
Yup, CDL installed and one of the two shafts removed allows you to drive around... no harm to anything.
A couple guys on here drove around for months that way. I've done it for a couple weeks at a time.
 
Yup, CDL installed and one of the two shafts removed allows you to drive around... no harm to anything.
A couple guys on here drove around for months that way. I've done it for a couple weeks at a time.

It will even help your gas mileage a little.
 
Be sure instructions to whomever is driving is the CDL must stay on or will toast the VC.
 
U joint looks pretty dry. I'd just pick up a used shaft Del
That was my 1st thought when I saw the pics. Its probably worth your time to get under there and lube the rear shaft, before you have the trick repeated out back.
 
I am currently driving my cruiser with the cdl switch on and no front driveshaft. It handles a little different. Feels a little tippy. Seems like it magnified my caster issues. I have a 3 inch lift though so if you are stock maybe it wont cause any of my issues.
 
Thanks guys. For all the help.

The plan is to order a new front shaft from cruiser yard.

When it arrives I will bring it to TOYOTA dealer and have the u joints replaced and have the shaft balanced and then I will reinstall back on the truck.

When I bring the front shaft I will also bring the rear shaft and have the u joints replaced and have it balanced.

Again, thanks for all the help guys. I went and got my f250 out of storage so for now it is not as urgent to get the cruiser back up and running. But I still want to enjoy it the few months I get to be home.
 
Back
Top Bottom