Need-a-Fender

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 28, 2003
Threads
37
Messages
279
Location
The Buttcrack of Idaho
I am in need of a new passenger fender, see picture. It's an old injury from the previous owner but I'm tired of looking at it. I have not been able to locate a used fender, new through a body shop is scary, and cdan is to far away. Are there any good online sources for body parts.

Jay
Fender-Damage.webp
 
Just keep watching in the "parting out" forum... You'll find someone close that has one.


I've had GINERICLC watching for one, but nothing has come up. I guess I need more patience.

Jay
 
I can't tell how bad the damage is from the picture but it is probably repairable cheaper than buying a new/used one unless I really can't see it. I even rebuilt a flare like that with fiberglass and a little filler and you couldn't tell the difference. A good body man could fix that with very little filler for only about an hour or two labor. (again unless it looks worse than the picture) I assume you are going to have to pay a shop to remove the old fender, paint the new fender and install it, probably alot more hours than repairing the damage you have.
Rusty
 
I can't tell how bad the damage is from the picture but it is probably repairable cheaper than buying a new/used one unless I really can't see it. I even rebuilt a flare like that with fiberglass and a little filler and you couldn't tell the difference. A good body man could fix that with very little filler for only about an hour or two labor. (again unless it looks worse than the picture) I assume you are going to have to pay a shop to remove the old fender, paint the new fender and install it, probably alot more hours than repairing the damage you have.
Rusty

The damage is worse than the picture shows, it was just the quickest picture I could find. The fender has a very deep crease in it from the ARB wing. I hate to have body filler in the front corner waiting for a bump to crack it. Thanks for the feedback.

Jay
 
I would still take it to a good body shop and have them look at it. If filler is put on correctly and thin it won't crack no matter how much it bumps or bends, it is only bad body work that people notice. In fact it would be very unusual to have a new fender installed that did not require a little filler as well. I have installed a lot of new panels and I can't remember one of them that didn't have some dents in it from shipping, storage etc. I watched a friend of mine rebuild the front lower bonnet of a Jaguar that his wrecker put a really big crease in, he did the whole thing without any filler at all. Not many body men can still do that but most can get it to where it won't take much and it would probably be cheaper than replacing. If you do go new, I would make sure you get an OEM fender, some of the aftermarket fenders don't fit very well.
Good luck - Rusty
 
Be bold, and just fix it!
When I bought my 80, the left side rear quarter panel was crushed far more than your fender is. It was flat! The taillight opening was less than 1" wide. In addition, the front of the roof was down 6" from standard and the front left fender was badly damaged. Both left doors were badly dented. The door handles were broken. The upper front door frames and window tracks were very bent on both sides. The sunroof tracks were crushed. The hood had several deep dents, and some of the front glass was crushed out! The truck had been rolled over. I repaired every part of the truck without replacing any original metal! It is all factory with no body parts replaced. Even the sunroof works fine! I have driven it all over the southwest. I get comments everywhere as to how good my truck looks. They cannot seem to know that it was rolled. There are very few visible signs, even if you know what happened. It looks great!
Now, what was your question?
This is not a Sentra. It is not a Chevette. It is not even a Corolla or Camry. The truck was made out of real metal. Just fix it and paint it up. It's a Land Cruiser!
 
Last edited:
Thanks for the encouragement Brian and Rusty. I guess I need to nut up and quit whining. It was when the previous owners bad body filler started falling out that I got discouraged.
Maybe I need to ask Santa for body tools this year.
flipa.gif


Jay
 
I learned how to do my own by watching the guy I spoke of above and by reading a couple of books. Practice is the best way though, all it takes is patience. I figure I can do a better job than most body shops because I am not trying to make money off of it so I can take my time. Again, properly applied filler will not come off or crack. Get the Eastwood catalog, they have lots of good tools and books and videos to make it easier. Painting is also not all that hard, again just a bit of practice, it all comes down to the prep work and patience.
Good luck, happy to answer any questions
Rusty
 
Back
Top Bottom