Mount full size CB, can I do this........?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 22, 2004
Threads
204
Messages
11,638
Location
Deep East Texas
Wanting to mount one of my full size CB's in my 80 series. Yes....'full size', please DON'T suggest a smaller CB (uniden 520/other), thank you.

Question: Can I drill holes in the rear of the center console and NOT hit anything hidden there?

The center console (97 model) has an inner lining, so I can't see if there is anything behind it. The rear heater vent is down low near the floor and my intended mounting point is about 1/3 to 1/2 way up from the floor.

Anyone know if drilling a few holes (just deep enough to install pop rivets) would hit anything there?

Open to suggestions for other mounting spots, but it doesn't appear the 80 series lends itself to having a large CB (fairly accessible) installed. Yeah...I know, "that's why folks use the small one". ;)

Help me out here guys (without busting my chops).

Thank You in advance.

Flint.

Mount%20CB%2080%20Series_zpsxnygg112.jpg
 
You can, but really - why not pull it & do a real nut/bolt with a washer?

That plastic is thin but with real hardware I had my big ~5lb fire extinguisher mount there & it sat on the floor. Neither my dog, rough roads, or backseat passengers ever made it loose. My $.02

Someone had a pic up of the console flipped over in a thread about the hinge needing repair - was here ~2wks ago.
 
I mounted mine back there with good/big Velcro from Walmart. I stow my Go Bag between it and the second row seat. Kinda muffles the speaker so I went to the truck stop ang got a remote speaker that fits below the parking brake handle for $12. Works great !
 
Yes. The only possible downside is if the rear seats are folded forward you MAY get interference.
 
Wanting to mount one of my full size CB's in my 80 series. Yes....'full size', please DON'T suggest a smaller CB (uniden 520/other), thank you.

Question: Can I drill holes in the rear of the center console and NOT hit anything hidden there?

The center console (97 model) has an inner lining, so I can't see if there is anything behind it. The rear heater vent is down low near the floor and my intended mounting point is about 1/3 to 1/2 way up from the floor.

Anyone know if drilling a few holes (just deep enough to install pop rivets) would hit anything there?

Open to suggestions for other mounting spots, but it doesn't appear the 80 series lends itself to having a large CB (fairly accessible) installed. Yeah...I know, "that's why folks use the small one". ;)

Help me out here guys (without busting my chops).

Thank You in advance.

Flint.

Mount%20CB%2080%20Series_zpsxnygg112.jpg
I mounted my bearcat 880 there without problems. I keep the mic under the arm rest on a retro fit sunvisor. I just took the bottom cover of the cb off and ran screws through the plate and the put the cb back together
IMG_20171116_175247503.webp
 
That's where I mounted my full size cb.
 
You can, but really - why not pull it & do a real nut/bolt with a washer?

That plastic is thin but with real hardware I had my big ~5lb fire extinguisher mount there & it sat on the floor. Neither my dog, rough roads, or backseat passengers ever made it loose. My $.02

Someone had a pic up of the console flipped over in a thread about the hinge needing repair - was here ~2wks ago.


Happy to pull it and use some type of 'backing plate' IF pulling the console is not some big affair. I've never had it out. Had everything forward of that off at some point, but not the console itself.
 
Yes. The only possible downside is if the rear seats are folded forward you MAY get interference.

Yes will need to check to see that I mount it low enough. Also that the console lid doesn't hit anything when opened.

Good point. Thank you for bringing that up.
 
I mounted mine back there with good/big Velcro from Walmart. I stow my Go Bag between it and the second row seat. Kinda muffles the speaker so I went to the truck stop ang got a remote speaker that fits below the parking brake handle for $12. Works great !


Yes, I always use an external speaker. PA speaker as well.
 
Get a smaller one...
20171016_215104.webp


Depending on the model, you could make a remote mount faceplate, and stuff the main unit out of the way. I remember seeing this years ago I think on a tacoma on some forum. He basically desoldered the faceplate and added one or two ribbon cables or cat 5 cables.. something like that to extend it.
I wonder if they have remote mount cb units like some of the Ham radios..
 
Get a smaller one...

Nope, don't want a smaller one. If I only used/needed it for a 'trail rig' that would be fine.

I like the features of my full size CB. Weather channels, full analog readouts, RF gain, Mic gain, PA, External speaker, NB/ANL, etc.

Radio has been fully 'Peaked and Tuned'.

But certainly agree...that smaller CB's can be mounted in places like the ashtray slot and be handy enough for average use.

Thanks to all...for your suggestions and replies. I have a little bit of direction now.

Flint.
 
The bolts in the base are all that holds it down - 2 or 3, I forget.

Simple to pull.
 
Nope, don't want a smaller one. If I only used/needed it for a 'trail rig' that would be fine.

I like the features of my full size CB. Weather channels, full analog readouts, RF gain, Mic gain, PA, External speaker, NB/ANL, etc.

Radio has been fully 'Peaked and Tuned'.

But certainly agree...that smaller CB's can be mounted in places like the ashtray slot and be handy enough for average use.

Thanks to all...for your suggestions and replies. I have a little bit of direction now.

Flint.
My stryker has all that in a small chassis, except analog dial. But I was just being a smart a** since you clearly put in the op to not say to get a smaller one.

Found the link.
CB Radio (Cobra 29) Mod & Mount in Center Console
 
Last edited:
The bolts in the base are all that holds it down - 2 or 3, I forget.

Simple to pull.

4 bolts in the bottom of mine. If that is all that is holding it in place, I will do that for sure. It will be interesting to see how the rear heater is set up underneath it all.
 
My stryker has all that in a small chassis, except analog dial. But I was just being a smart a** since you clearly put in the op to not say to get a smaller one.

So you're running an altered 10 meter radio?
 
The bolts in the base are all that holds it down - 2 or 3, I forget.

Simple to pull.

And 2 screws, one on either side of the shifter console. ;). You should definitely take out the console a have a look. It's about a 5 minute job but 3 of those minutes is getting all the junk out of the console. I'm no HAM snob but if I were going to hard mount any radio it definitely wouldn't be a CB. I went all around this myself and even hard mounted a smaller uniden in my first 80 in the center console itself. I removed the speaker and mounted it as you can see in the below thread. In my current 80 I just use a handheld midland unit but with an antenna run to the back corner. Most of the VHF/UHF radios have the weather bands as well. If I mount anything in the future it'll be HAM.

Incognito CB install
 
Last edited:
So you're running an altered 10 meter radio?
No mods on this one, out of the box it is 40 watt capable if you set it up that way. But I have it set up just for cb duty on the standard 4 watt setting. I would much rather stick one of my cobras or galaxy radios in there since I prefer the knobs vs the digital read out. Since I live in Los angeles, I needed to keep it low key and compact, the chrome dials would attract the crackheads to bust a window out.
 
Here's my big radio mount, but it involves a Tuffy...
RCI2950TuffyMount_IMG_1255.webp

Sorry, it's a little messy n there right now.
 
  • Like
Reactions: MoJ
Back
Top Bottom