missing on cylinder 6

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 8, 2006
Threads
6
Messages
58
no bubbles, no froth, CEL 25

did the wet test on the line, checked, and swapped #3 plug with #6.

good spark @ the rotor, and at the end of #6.

wiggled the harness, reseated the injector plug (PITA)

EFI relay is hot. Likely culprit?
 
Last edited:
Try resetting the CEL and see if it comes back. Is the engine running bad or did you just get the code?
 
Check the wiring harness that runs behind the EGR valve for any wires contacting ground. Sometimes its an injector wire and it may only be one of them causing the misfire.

Dan.
 
Same exact thing happened to me...

There was a pinhole leak in my heater hose just above the injector.

Had been dripping on it for a while and the heat up / cool down process eventually cracked the injector and fluid got in.

Killed the injector and that #6 is a bitch to get to.

I did not have time to F with it so I paid a guy to do it to the tune of about 6 hunsky...
 
Is this a dead miss....as in missing all the time or is this just noticeable at idle/low engine speed?

Anything happen before hand, did it start after you did some other motor work/maintenance?
 
all the time. now it is idling low too, say 450RPMs.

checked air hoses, vaccum connections, and #6 inj. wiring harness. the code 25 is gone for now, I assume that when you read them they go away
 
Well, I'd say no to the EFI relay....B/C I'd expect problems all across the board not just on #6. So if you've got a dead miss (again all the time) and you have spark then start with the basics.

I don't think you'll find an answer but run a vacuum test, see if she holds steady vacuum, and or a compression test on #6. I do not think you'll find anything there, since it's probably a fuel issue. I doubt you have a bad injector but who knows.

After install of a freshly rebuilt 1FZ I swapped the #5 and #4 injector plug which gave a very slight miss at ilde. It would disappear off-idle, and otherwise ran fine. Your problem for sure sounds different.

And yes, once you clear the code it will temporarily be gone. Dunno if any of this helps.
 
See if you can do a resistance test on the injector. It is a pain to get to but it might be possible. The FSM can tell you how to do it. That will tell you for sure if it's the injector that's bad.

Same thing happened to me as Skillet. But when my injector went bad, it was throwing code 25 and 26 simultaneously.
 
I think it's the dreaded Head Gasket failing. Try this after a freeway run: remove the #6 spark plug and see if it's wet. If it's really wet, you may see some steam coming off of it. If so, it is probably coolant sneaking in past the head gasket and drowning out the spark.

I hope not but just check it to eliminate possibilities.
 
I think it's the dreaded Head Gasket failing. Try this after a freeway run: remove the #6 spark plug and see if it's wet. If it's really wet, you may see some steam coming off of it. If so, it is probably coolant sneaking in past the head gasket and drowning out the spark.

I hope not but just check it to eliminate possibilities.

plug was clean, but not steam cleaned. plugs are within 2kmi. old. I didn't see any indications of the HG going bad as of yet. No leaks at the HG around the rear of the block.

really scratchin my head here. Fuel dilevery seems to be the most logical, but it looks like I will need to remove the upper intake to even get to #6 in any meaningful way:doh:
 
plug was clean, but not steam cleaned. plugs are within 2kmi. old. I didn't see any indications of the HG going bad as of yet. No leaks at the HG around the rear of the block.

really scratchin my head here. Fuel dilevery seems to be the most logical, but it looks like I will need to remove the upper intake to even get to #6 in any meaningful way:doh:

#6 plug may not be clean and I expecedt that. But, I need to know if you see moisture after a hard run.

If there's a HG leak, the coolant won't always show up on the outside of the block. Most HG leaks on this board have shown up at the same area of the fire ring, near the cylinder wall.

Fuel delivery issue to just one cylinder is unlikely. These injectors are robust and very reliable. Both of my 80's had the FI's tested before and after cleaning and the numbers indicated no signs of performance issues. Both sets came out of high mileage engines.

Humor me and pull the plug :D
 
#6 plug may not be clean and I expecedt that. But, I need to know if you see moisture after a hard run.

If there's a HG leak, the coolant won't always show up on the outside of the block. Most HG leaks on this board have shown up at the same area of the fire ring, near the cylinder wall.

Fuel delivery issue to just one cylinder is unlikely. These injectors are robust and very reliable. Both of my 80's had the FI's tested before and after cleaning and the numbers indicated no signs of performance issues. Both sets came out of high mileage engines.

Humor me and pull the plug :D
I did pull it, no moisture, oil residue or otherwise. Pulled it after making a 20 minute run. Engine temp was in the normal range when I pulled it.
 
Dead miss on #6
Good spark to #6
No moisture on #6 plug

Therefore:
It's either the injector or the wiring harness.

-B-
 
let the irritation......begin!!!!

I will pull it into the garage tomorrow and commence tearing apart the harness first (easier to get to), then, assuming I find no hard faults, I will pull the upper half of the intake to get to the dang diggity ang fuel rail and test the injector for resistance and function.

wish me luck boys, I am gonna have to lock up the shotgun to keep from blowing it to pieces in revenge LOL
 
FYI,

I've swapped injectors on my '97 without pulling the upper intake. Just took the throttle body off, but yes it did suck and no it was not easy at all.
 
I did pull it, no moisture, oil residue or otherwise. Pulled it after making a 20 minute run. Engine temp was in the normal range when I pulled it.

Ok, that's a relief. You can rule out the HG failure at least :cheers:
 
Ok, that's a relief. You can rule out the HG failure at least :cheers:

That's not a relief! :flipoff2:.

HG is like a time bomb and will blow inevitably/eventually!

just keeding :D.

It will be really PITA to remove the #6 injector without removing the upper intake. You can have good spark but if the wiring for the #6 injector connector is bad (or burnt) any where (especially near the EGR pipe) you will have the misfiring problem.

I've got some pix and info on the following thread:

https://forum.ih8mud.com/80-series-tech/169934-sort-stranded-code-304-help.html
 
Last edited:
read through those other posts....going outside with a razorblade now to expose all them stinkin wires...roll of 'lectric tape on hand to verify any temporary repairs :D
 
Back
Top Bottom