Max speed for locking the Center Diff?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

OK.........I'm old skool, own an 80 but prefer the 40's 45's 60's for me......WTF would ya want to engage it at any speed over 15 mph.......I would treat it like front lock outs......if ya' think you are gonna need em.....lock 'em before getting in trouble.
Butch

Shift on the fly center locking? The newer vehicles use either pnuematics, vacuum, electric (toyota) motors, or electric solenoids to activate an internal dog clutch. It works very similar to a manual transmission. Think of the actuator as a synchro. The dog clutch isn't immediately engaged, that's why the light doesn't come on right away. It's engaged when the driveshafts are rotating the same speed..

I think it doesn't matter what speed you engage them on the 80, there's not that grind, strip and clunk in the new stuff.

SJ
 
I think it doesn't matter what speed you engage them on the 80, there's not that grind, strip and clunk in the new stuff.

SJ

I fully understand all of that , in fact work on the s*** all the time.....my point is, what situation would arise where you would suddenly need the center diff lock say at 60 mph?
 
Last edited:
Wrong. You're comparing cars to trucks. You're insisting that tires are the only wear item; they're not. You're insisting that just because it doesn't break, it's not being worn prematurely. You're comparing a car in a drifting situation to a truck that you don't want to try to drift. Low CG vs. high CG. Your entire arguement is based on a completely different vehicle and situation.

I will agree that it makes no difference what speed you choose to engage it, only the terrain you engage it on.

-Spike
 
Last edited by a moderator:
I fully understand all of that , in fact work on the s*** all the time.....my point is, what situation would arise where you would need the center diff lock say at 60 mph?

Climbing into the mountains of CO thru the passes, did it all the time. Snow to dry pavement? A hunting/humping VC? Sudden ice, gravel, sand, snow?

That's it's advantage over the stop and cram IMO. It's not an offroad advantage, it's an on road at speed advantage. When I get tired of medium density slow fast traffic in Chicago I'll do it, that center diff lock massively settles the truck fore-aft wallow.

SJ
 
Wrong. You're comparing cars to trucks. You're insisting that tires are the only wear item; they're not. You're insisting that just because it doesn't break, it's not being worn prematurely. You're comparing a car in a drifting situation to a truck that you don't want to try to drift. Low CG vs. high CG. Your entire arguement is based on a completely different vehicle and situation.

I will agree that it makes no difference what speed you choose to engage it, only the terrain you engage it on.

-Spike

Spike, you miss the point completely. I've been locking centers on pavement for 16 years man. Not drifting, driving the frickin car. There isn't a single person that rides along that would know it either. "Bind" only happens in a really tight turn. With the wheelbase on the 80 you can drive in the city and never 'bind' the axles, I do it all the time.

You have to get a calculator out and draw turning radius where you say bind occurs. I say you get more bind parking your truck, then you ever will driving it with the center locked in normal driving. Lock your center diff tomorrow and try it. Tell me when bind occurs. Take a week to do it, I have more than 4000 miles logged with my center diff fully locked, dry pavement the majority. You won't break it doing a little research.

IMO/E what causes driveline wear and failure is high torque with low turning radius. That's innate to every awd/fwd car and truck on the road.

We don't have the problems Rovers do with overheating of the transfer case.

It's not abuse, it's just understanding how vehicle dynamics work. I find any blanket statements about wear or handling in locked center diff awd to be unsupported opinions. I work on locked center cars as my living, cars built and designed with center lockers for ROAD use. I don't see the 80 any differently, only that it's built like a sherman tank in comparison.

Easy to shift the logic over to it.

SJ
 
I don't miss the point at all. You think you're right, I think you're misleading a bunch of people. Perhaps you should call up Toyota and explain to their engineers that they've been doing it all wrong, and that extra $1000+ of crap that they put into the transfer case on their full-time 4wd vehicles is unnecessary.

You have your opinion, I have mine and Toyota's, apparently. The only reason I'm even still discussing this is so a bunch of people don't run out to their 80's and push the button just because Sumotoy writes a nice post. I'm done now, I really hope I am.

-Spike
 
I don't miss the point at all. You think you're right, I think you're misleading a bunch of people. Perhaps you should call up Toyota and explain to their engineers that they've been doing it all wrong, and that extra $1000+ of crap that they put into the transfer case on their full-time 4wd vehicles is unnecessary.

You have your opinion, I have mine and Toyota's, apparently. The only reason I'm even still discussing this is so a bunch of people don't run out to their 80's and push the button just because Sumotoy writes a nice post. I'm done now, I really hope I am.

-Spike

Welll actually, I'd like to call Toyota and THANK them for putting in thousands of of dollars into the VC in the HF2AV center locker transfer case on their full time 4wd vehicle which is unecessary. That is "doing it all wrong", and I applaud them for it!

In the meantime, to the original post and question in post 1. You can lock the center diff on the 80 at any speed. The risk is no higher on dry pavement than on lower cf. The best time to lock the center diff is when driveshafts are rotating the same speed, wheel straight ahead. Which means exactly that the worst time is during a turn, on any surface, at any speed.

I was hoping to educate how AWD works, and dispel some of the misconceptions of it. I did not mislead anyone, I'd be happy to defend all of the above in any discussion, and/or demonstrate the safety benefits at a variety of venues.

Spike, come to Steamboat in February. There is no doubt in my mind that you will change your thinking. I respect that you have an opinion, it's just tough to support.

:cheers:

SJ
 
Last edited:
Im just going to say 2 things, I have 2 trucks an 80 and 4runner.

The 4runner with CDL and I turn the TIRES will chirp and I can feel the binding on pavement on most 90 degree turns. This is with 32 inch small ATs

Now the 80 with 35s I hit the CDL and take a turn it feels stiff but nothing really happens, I think tahts becuase she weighs 6000 pounds and has the softer rubber and 35s.

I know for a fact with CDL on my 4runner is BINDING and it even feels painful to take a 90 degree turn on pavement.
 
I've frequently run the CDL locked at higher speeds on low-traction situations, it's particularly nice on gravel roads when you are trying to 4-wheel-drift and the ABS wants to kick in as you hit the chatter sections as you pitch into a turn.... I've also switched it for snow and wet situations....I can't stand how ABS works most of the time and find better cornering and braking control with it switched.

I've got it locked in now, runnin 75mph...course, with no rear driveshaft installed, it's necessary. ;)

IMO, locking in on dry pavement isn't a wear issue, but one of added stress. At road speeds, the bind is minimal, since most turns are relatively wide and the scrub of the tires is insignificant. I can see definite bind concerns at lower/city speeds tho.
 
Im just going to say 2 things, I have 2 trucks an 80 and 4runner.

The 4runner with CDL and I turn the TIRES will chirp and I can feel the binding on pavement on most 90 degree turns. This is with 32 inch small ATs

Now the 80 with 35s I hit the CDL and take a turn it feels stiff but nothing really happens, I think tahts becuase she weighs 6000 pounds and has the softer rubber and 35s.

I know for a fact with CDL on my 4runner is BINDING and it even feels painful to take a 90 degree turn on pavement.

Locked center turning radius induced binding is directly proportional to 2 variables, wheelbase and turning radius. That's the effect you note, and I too have had similar observations in my locked center 87 4R. Tire height really doesn't matter, since binding only requires torque and driveshaft (attempted) differentiation, read it's not a tire speed variable. Tire compounds don't really affect binding, unless different sizes front and rear. Their compound may cause 1 to scrub sooner than the other however. Interesting to note, I'm still running the Blizzacks 12k mi later (about the softest gummy bear you can buy), and I have very little tire wear even noticeable, and I run locked center quite often. Go figure.....


SJ
 
Last edited:
Does it really matter about having the CDL engaged during turns?

I'm comparing it to the Jeeps with Selec-Trac or whatever they called it.

You could have 2H, 4PT, 4FT, and 4Low. The 4 Part Time was more like an AWD system and the 4 Full Time was as if you locked the hubs and engaged 4WD in a solid axle Toyota.

What's the issue with steering? Unless you lock your front axle the difference is minor. In real world driving does it really matter? Unless you are doing tight donuts all the time lock it or don't. I can't forsee any 'extra' wear or breakage.

Push the button and compare it to not pushing it. If you like it locked leave it locked. I would think that you would only consider pushing it if roads warranted more stable traction.

I think I'll drive to work with the CDL engaged and the factory lockers not engaged.

I bet the only difference will be less 'clunking' when stepping on it and letting off. I notice a little less play. That's about it.
 
I have a card in my 100 that says to not lock or unloack the CDL at speeds above 65MPH. Because the 100 has the CDL switch standard it's my guess they state this on the 100 but say nothing about an 80.
 
After I recieved and installed my CDL switch I took it out for a drive to see how it affected driving in various conditions. One if the conditions was dry pavement. In a tight right hand turn ging up a steep grade the truck bucked and the tires sounded like a pack of baying dogs (BFG All Terrane TA's, 32's). The binding was not only evident, but alarming. With the CDL not engaged the truck makes the same turn smoothly with no bucking or tire chirping. So, do I want to put the additional wear on the tires? Or the additional load/stress on the driveline? What benefit do I recieve in handeling/performance/etc. by locking the CDL versus doing my normal daily driving with it unlocked?

To me it seemed like a no brainer to leave the CDL unlocked unless I was in an envirnment that resulted in lower traction than paved surfaces. If the driveling binds, there is friction. Friction causes heat and wear. I see no benefit to driving with a locked CDL that offsets the increase in possible wear. I mean, I enjoy driving my three 80's more than I enjoy working on them (that's why I own three 80's, not three Dodge's, Ford's or Chevy's). I have replaced too many u-joints, drag links, main bearings and other lubricated parts that experience metal on metal contact to believe that what I experienced while driving my trcuk on pavement with the CDL locked would eventually result in me working on my truck to replace/repair some broken/worn parts.

Right on. It's always best to run all lockers unlocked until you need their added traction. Everything on your truck will last locker this way. :)
 
I'm going to have to take the cruiser out for a spin with the center diff locked up just to try it out. I never would have thought about trying this since I'm used to my old FJ60 where it's work to put it in 4wd.
 
Tire height really doesn't matter, since binding only requires torque and driveshaft (attempted) differentiation, read it's not a tire speed variable. Tire compounds don't really affect binding, unless different sizes front and rear. Their compound may cause 1 to scrub sooner than the other however. Interesting to note, I'm still running the Blizzacks 12k mi later (about the softest gummy bear you can buy), and I have very little tire wear even noticeable, and I run locked center quite often. Go figure.....


SJ

Hey bud, thanks for the reply.

I was just mentioning the tire size, rubber compound, vehicle weight as to why the cruiser doesnt chirp. I bet in my cruiser had some ATs 31's with a harder compound then my MTs it would chirp on simliar turns thats all.

Cheers and safe driving!
 
I can't see any reason not to, I've never thougt twice about doing it, even my track prepped quattros all run center diff locked.

HTH

Scott Justusson

I imagine that a tracked-prepped quattro is used primarily for rally. Certainly, no stock Audi Quattro or any other AWD vehicle has a locked center diff. The simple fact that your 80 has a lockable center diff implies that there are times when it is best to not lock it.

I'm sorry, but I have to say that your suggestion is best not taken by others.

Jer
 
I imagine that a tracked-prepped quattro is used primarily for rally. Certainly, no stock Audi Quattro or any other AWD vehicle has a locked center diff. The simple fact that your 80 has a lockable center diff implies that there are times when it is best to not lock it.

I'm sorry, but I have to say that your suggestion is best not taken by others.

Jer

Actually, my track prepped quattros are primarily tarmac track cars. Even as late as the motorola cup, several new S4's were known to weld the center diffs. Th handling on road courses of quattros with locked diffs is higher than quattros in Rally. The story I shared earlier is interesting too, audi delivered the press cars with center diffs locked all the time. Road versions. Then from 1982-1988 audi delivered all Production *Road* going (repeat, luxury road machines - including my favorite turbo quattro wagon....) vehicles with air locker center and air locker rear (and a push button for ABS off too, btw).

What that indicates to me, is that there are times *on road* where it's exactly fine to lock the center diff. And that Audis suggestion is best taken by those with the mindset that the center diff is some sort of special off road thing. IME, there is no question that performance and handling increases at speed with the center diff locked. Even in my 80. Those with 7pin mods can easily test this out any time.

Paradigm shift?

SJ
 
Last edited:
More locking cernter diffs at speed

As I lent the wife the 80 this week, while her quattro was in my shop for maintenance, I realized that here is the $55k flagship quattro model of 1991 with an electronic locking center diff (plate type center, also with torsen rear, btw). It will lock center differential with any axle speed differential (turns exempted unless already locked), at *any* road speed., up to it's maximum 155 top end. I see no 'loss of control' issues....

It also might be interesting to note that the 80 with the HF2AV also is a step towards center diff locking on road without any road speed limitation associated with the VC. The haldex also does that electronically at any speed as well.

The designer of Torsen center diff application told me and a fellow race buddy, the main reason for the torsen application center vs locked, was the high desire to have ABS function during braking.

That would also be why Toyota added the VC center diff as well. It retains ABS AND allows full lockup.

All these toys mimic a locked center diff. I say just lock it, you'll understand the desire.

Cheers

ST
 
Back
Top Bottom