Lowering back to stock

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 30, 2014
Threads
25
Messages
213
Location
San Francisco, CA
I am looking to possibly restore my 80 (‘97 LX450) back to stock or as close as possible. Right now, it has a 3.5” rear Dobinsons heavy springs and 2.5” in the front, longer control arms, caster correction plates, adjustable panhard bars, 5.29 gears, and 35” tires plus armor.

As I understand, lowering will involve something like either stock factory springs or OME 861/862 combo, and matching shocks. The control arms are adjustable and the caster correction plates have to be removed. I might retain the front bumper but most of the roll cage and swing outs would be gone. Keeping the sliders. All in all, I think the OME pair should handle the extra weight and keep stock-ish height?

Wondering what tire size will match the 5.29 gears. With the 35s and the armor (roll cage, swing outs, front/rear bumpers), it is pretty sluggish right from the start. I am aiming for something slightly larger than stock - like a 285/70/17 maybe? I realize that cruising RPM will be higher but if that doesn’t bother me much, is there any other downside? Am I missing anything else?

Not trying to advertise my listing - in fact, I am considering lowering my 80, delisting it from classifieds and just enjoying it as a daily driver since I’ve put plenty of effort and $ into it :D

Thanks for reading!

1997_lexus_lx450_1997_lexus_lx450_8ffb7757-868e-444f-8084-2e (9).webp


1997_lexus_lx450_1997_lexus_lx450_9b935536-c966-43ca-a750-05 (1).webp
 
Last edited:
Does that thing time travel when you hit 88 mph? Curious about all that tubing...
You’d have to buy it to find out 😭

I just got back from a test drive after tossing out the storage drawers and all the recovery gear and spares etc inside. It is already much nicer to drive. So I am recalculating and recalibrating plans, lol.

I still want it lowered so family doesn’t make faces when climbing in. I have a m-in-law visiting soon and some family trips in the near future so gotta factor that in.

Maybe I do not go down to stock but find some middle ground. The roll cage is nice DOM tubing, I forget 1.5 or 2” OD. I can remove just the upper section, there are allen bolts at about bottom of windshield height - lose some weight there. Or get rid of it all including the swing outs. Choices choices!! :D Honestly, the roll cage and armor is more use in the urban jungle that is today’s traffic and crazy drivers in the SF Bay Area than off-road 😭

Edit: by the way, the roll cage and entire armor except the front bumper are the handiwork of another Mud member. I don’t recall his id but I can look him up if you are interested. He did a fantastic job.
 
That exo cage looks nicely done, but the problem is, it's an exo cage. On their best day, they're ugly (my opinion) and heavy (objective fact). Meanwhile, while you're trying to protect every square inch of sheet metal for damage, you're bound to put a rock or a tree right in the middle of a space with no tube. I'd put it on a weight loss program and see how you feel about it.
 
That exo cage looks nicely done, but the problem is, it's an exo cage. On their best day, they're ugly (my opinion) and heavy (objective fact). Meanwhile, while you're trying to protect every square inch of sheet metal for damage, you're bound to put a rock or a tree right in the middle of a space with no tube. I'd put it on a weight loss program and see how you feel about it.
I agree 100%. The exo cage has to go! It is tempting to keep it but it will fight daily driveability and family usage every step of the way. Just opening the swing outs requires my presence. I mean it is rather simple but requires following 3-4 steps that other family members refuse to learn.
 
I found a set of stock alloys and 275 70r16 tires and swapped out the 35s with the steelies. Obviously, it looks cartoonish but surprisingly drove really nice. Acceleration off the stop didn’t improve much but overall responsiveness is better and freeway driving was much smoother. I suspect the biggest change would be when I lose the expo cage - I think it is not just the weight but also the drag is adds - which grows exponentially in relation to the speed. So the faster the truck goes, the harder it has to work to maintain that speed.
 
Budget route:
Dobinson stock height springs (will net you 1") and tokiko shocks.

View attachment 4238615
Thanks! Looks great. While searching for information on lift and springs, I ran into my post when I had just bought the LX450 and a picture of the truck from back then - most importantly my comment that despite the 35s, the truck felt pretty good to drive with stock diff gears. If you look at the picture, it has a lightweight front bumper and not much else 😀 So today, I am stripping the armor!!! Be gone, leave my truck and give me back my old truck!! 😅


 
If it were me, I would lose the "exo cage". It's not a well thought out design and I doubt it will function very well. Will it help in a flop or a rollover, likely it will help somewhat but for the added weight and the poor design...I think you would be better off with it being removed.
 
If it were me, I would lose the "exo cage". It's not a well thought out design and I doubt it will function very well. Will it help in a flop or a rollover, likely it will help somewhat but for the added weight and the poor design...I think you would be better off with it being removed.
I agree - let’s just call it a good proof of concept that a 80 can be wrapped in a roll cage 😅 Oh well, you live you learn. Yep, by end of day today, I am stripping it all off - come hell or high water 🎃
 
Thanks! Looks great. While searching for information on lift and springs, I ran into my post when I had just bought the LX450 and a picture of the truck from back then - most importantly my comment that despite the 35s, the truck felt pretty good to drive with stock diff gears. If you look at the picture, it has a lightweight front bumper and not much else 😀 So today, I am stripping the armor!!! Be gone, leave my truck and give me back my old truck!! 😅


I prefer that look.....and its practical as a daily too.
 
Almost there with getting rid off the armor. Several interruptions, owing to kids/halloween, but the big part was getting the upper exo cage off which took a great deal of finagling. Few more bolts and this 80 will be ready for some light weight TG front and rear bumpers again like it used to rock 😀

Still debating on what tires and wheels to run. I am leaning towards 33x11.5.

WIP pic

IMG_2063.webp
 
I need help with the rear cross member. It was cut off to install the custom exo cage and bumper. What are my options since it needs welding - I can get it welded but where do I find a nearly cut crossmember since it can’t be unbolted at a junk yard?
 
The truck is officially off all classifieds listings. I am keeping it 😊

The back to stock might have something to do with a brand that must not be mentioned on this forum 😭

I am told hell freezes over if you own these two last of their breeds 🤣

IMG_2018.webp
 
Back
Top Bottom