Lound thunk...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 8, 2016
Threads
16
Messages
55
Location
Lake Jackson, TX
Everytime I put my truck into drive, or into reverse, from either park or neutral, there is an initial loud clunk. There is also a smaller clunk if I accelerate really fast and then let up on the gas really fast.
Has anyone had similar issues?
 
How many miles on your drivelines & u-joints?

I'm betting on slop / wear there.
 
mine does this when letting quick off after acceleration, i haven't gotten to the u joints yet there were a couple driveability issues that took priority.
 
Can you be more specific where the clunk sounds like it is coming from? Worn flanges on the hubs is also common as are the UJ's.


Exhaust slightly bent or not mounted tightly enough and hitting the chassis rail over the axle has been known (mine).

Sometimes rolling very slowly in forward and reverse can bring up a soft squealing noise, this is classic rollers breaking up in the UJ's, eventually becomes a clunk as they rust and break up.

regards

Dave
 
Mine made a bell like sound for a very long time. Hit the driveshaft with a wrench, its the same ringing sound. When checking the driveshafts by hand I could only get rotational movement from the driveshaft yoke. I assumed that the yoke was worn so I stopped looking. Last week when greasing the rear u-joint on rear driveshaft something didn't look right. Later that week, the u-joint failed. The ringing noise when from a ring to a ring thud.

I should of used a large pipe wrench to check the u-joints for play as turning by hand didn't work. What was strange was I could get the ringing nose when I checked for play in the yoke. I haven't replaced the u-joint yet so I can not confirm if the ringing noise was from the u-joint or play in the slip yoke.

I also rebuilt the front diff my self at 210,000 mi. Had to remove the pinion to replace the seal and later the flange to get the pinion to stop leaking. I replaced all the u-joints at that time. I heard a clanking noise back then and assumed it was from my crappy job of re-tightening the pinion crush sleeve and nut. There may of been play in the u-joint when I replaced them. So far with rear driveshaft removed, there is no noise from drive line but its only been a couple days of driving with rear driveshaft removed. Someone posted something about different size snap rings sizes for the u-joint to take up the play in the u-joint but I cant find that post now.
 
Last edited:
163k miles on everything. I'll have to check out the u-joints.
 
I'm in for the u-joints.
 
So, I noticed today that it only makes a clunk when going in and out of reverse, or if I am accelerating in 3rd gear and let it up. Does this still sound like a u-joint issue?
 
Mine does the EXACT same thing. We initially thought bad u-joints as well, however we couldn't turn the driveshaft to find any obvious play. Interested to see what happens.
 
Mine does the EXACT same thing. We initially thought bad u-joints as well, however we couldn't turn the driveshaft to find any obvious play. Interested to see what happens.

Hm. Do you have any other thoughts as to what it could be? I know my front right wheel bearing is going out. Other than that, I hope it's not a trany issue...
 
I CAN tell you that I have recently had the transmission flushed at the dealer and the kick-down cable adjusted. I didn't own the vehicle long before I did this so, I can't give you a before and after. However it seems those jobs did little to nothing to change the sound. It HAS to be play somewhere either in the t-case, driveshaft(s), ...etc. Sounds metallic.
 
So, I noticed today that it only makes a clunk when going in and out of reverse, or if I am accelerating in 3rd gear and let it up. Does this still sound like a u-joint issue?

Off the cuff, yes.

You're changing the tension / which side of the DL splines are engaged - or if the U - joints are under compression / slack.

Quality time with the grease gun hitting all the DL & UJ's 'till proper grease shows on joints & expands the splines the spec amount (only 2-3 pumps as maint, not sure your personal need) ---- I'd do that all 1st as the quick/dirty before you chase this further.

Grab cardboard, slide under, grease all your zerks - 160K is primetime in my mind for a Cruiser that hasn't been greased for ~75K to start complaining about it, and letting you know it.

Pop your FR grease plugs on the knuckles & dip w/ a chopstick/ziptie/whatever - they may want a good 10-20-30 pumps each side too. You're already there, and if there's still grease in the gun, why not - right?

The plugs are literally the square head pipe plugs you see on top the knuckles, if you get there.

GL!
 
I would grease the ujoints well and the slip joints lightly and then see if it goes away. Cheap and easy test. John

This ^^^^ I had a similar issue and I did have very dry driveshaft yoke. Issue went away after I put some grease in it. There was minor u-joint play, but be careful, after I greased them up I could not get them to move and my guess is that the play is small enough that the grease helps mask it. Failure is imminent so I am replacing them
 
I had this issue on a Subaru and found that if I had someone in the car with the hand brake on ( it was stick shift) and put it in first and let the clutch out then do it in reverse I could see it move almost a half a turn. I'd try and get someone in the truck and put it in drive then reverse with there foot on the brake and get a good vantage point not where you'll get run over and watch the drive shaft
 
mine is a solid clunk if i let off the skinny pedal really quick. If i drive it easy it doesnt make any noise. my wife is using it for the next 3 weeks until she gets her truck back i will dig into it then. if i take it apart now and have to wait on parts there will surely be trouble!
 
19 posts of advice and we have no idea what vehicle we are working on.......:bang:
 
Back
Top Bottom