lift

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 7, 2003
Threads
402
Messages
13,956
Location
lebanon,pa
Website
www.facebook.com
so i almost hate to do it...........

i have a lift question...

thinking about an ome lift.
looking to put 33'' under it..whatever the metric size is, the one that's just under 33'' true measurement.
thinking about a 2-3'' lift.
i'm not looking to stuff the largest size possible. but is that going to be too much wheel well left over?. thought i've seen that 35'' fit with no lift.
 
i personally have the j spring setup with a 2" coil spring spacer up front...i love the way it looks.i sit level with most of the weight up front.ARB,WINCH.also i am running 315/75/16....i was running a set 0f 305x75x16;s before the lift...good luck on your lift
 
I have the OME Heavies 850,863 and they rock.. Its a perfect lift for 285's and you can load the back full of stuff and it will sit perfectly level when you need it most.

IMHO if you get the shorter springs in the back for DD it will look level but when you load her up to hit the mtns or the beach it will ride low in the rear. Now isnt one of the reasons for the lift to reduce rear sag?
 
I have the OME Heavies 850,863 and they rock..

not quite up to speed on teh various ome numbers. which i assume are spring lengths in cm's?
what "size' lift do you have?
 
The spring rates and numbers can bee seen on Slee's site
Slee - Springs

For my setup 850 863, there will be a 2.5 inch increase over stock in the front with 250lbs added to the front. The rear will be 2.5 inches with the addition of 440lbs in the rear. Take out all the weight and you will have nearly 4 inches in the back and 3 in the front.
Of course it all depends on how worn out the oem springs are on your truck. Some may get less of a lift than others. Mine were very bad and the back end sagged a bit.
 
I have 315's with no lift and no gear change either. It is hilly with stretches of flat land where I live so regearing is not necessary for me IMO. These 315's will probably scrub if I take them off road but the 285's didn't when I took them down some washed out trails heading for the river. To run my 315's off road I'm planning on going with the front heavy/rear medium with a 1 3/8" spacer front and rear. Also I'll have bumpstop spacers. I'm light weight (as light as I can be) with no bumpers and will only put tube on later with a possible winch. I'm going to the same spot today with the 315's on so I guess I'll know if they'll scrub for sure now. I would get the tires first and see what you think unless you are planning on immediate hardcore off roading.
 
I just installed the OME heavies with 295/75/16s on my otherwise stock rig. I got 3 inches of lift in the front and 3.5 in the back. It would seem when I and bumper and winch to the front, I will need a spacer up front.
Very happy with the ride so far.
 
I'm assuming you are talking about your FJ 80. Here's what a rig with our 2.5" suspension system looks like
16.jpg
 
i vote medium rears and heavy fronts in the 2.5 variety and 33's/285's. Here is a white 80 w/ that setup next to mine w/ the OME J (3.5) and slee 4'' front on 35's. FJ-80's fit 35's easier than fzj-80's it appears on low/no lift scenarios. Im very impressed w/ the ride of the white rig on 33's w/ heavy/med combo and slee blue bushings. (and it has ARB bumper and 3/4 lenght rack now.
URE426009.jpg
 
i was really hoping some one would try and talk me out of lifting it.
i see now what i must do....hide a lift kit from the wife, then hope she does'nt notice it on the truck...
 
Don't mention the idea of a "lift" to your wife. Just tell her the saggy springs and leaky shocks need replaced and that it will ride much better after replacing the suspension. Totally the truth.
 
i was really hoping some one would try and talk me out of lifting it.
i see now what i must do....hide a lift kit from the wife, then hope she does'nt notice it on the truck...

Why are you lifting it? 33's do look small on the lift kits. If you don't need a lift, go OME stock height, which will give you a bit of lift over your old factory springs, and run the 33's. Will look perfect.

On 3" of lift you are going to want 35's, trust me. 4"+ starts making the 35's look small. 80's eat tires visually when you start lifting. To get an 80 to really look like it has oversized tires once you've lifted it, if that is what you are after, takes 37's.

Your tires will look bigger on OME stock height than OME medium by a long shot.

33's on OME 2.5 and 35's on OME 2.5. The 35's are properly proportioned, but not oversized by any means.
OME on 33's.webp
OME Medium on 35's.webp
 
Why are you lifting it? 33's do look small on the lift kits. If you don't need a lift, go OME stock height, which will give you a bit of lift over your old factory springs, and run the 33's. Will look perfect.


this one would'nt need a lift at all. but if i'm going to freshen up the suspension i want something out of the deal. and i'm sure there will be a trip to the mnts or two.
15yrs and 188k, i'm sure shes-a-sag'n.
i like the top picture more.
 
If you are just going to drive it on the street, I'd put 285s on it and call it good. That will increase your ride height about an inch. Once you get the feel for the ride with new tires, you can decide on a lift.
 
I have 315's with no lift and no gear change either. It is hilly with stretches of flat land where I live so regearing is not necessary for me IMO. These 315's will probably scrub if I take them off road but the 285's didn't when I took them down some washed out trails heading for the river. To run my 315's off road I'm planning on going with the front heavy/rear medium with a 1 3/8" spacer front and rear. Also I'll have bumpstop spacers. I'm light weight (as light as I can be) with no bumpers and will only put tube on later with a possible winch. I'm going to the same spot today with the 315's on so I guess I'll know if they'll scrub for sure now. I would get the tires first and see what you think unless you are planning on immediate hardcore off roading.

I just back from exploring a few new spots and visiting my Aunt & Uncle at the lake while I was at the river. Anyway, it started raining and I didn't go as far down the trail as I have with the 285's. I stopped short since I was by myself, don't have a winch, don't have lockers installed, and can't get a cell signal there. I did go through a descent sized mud hole that hit pretty hard and I didn't hear any scrubbing. That said, I have heard a little scrubbing before when turning onto my road while going pretty fast and a hard turn in.
You can get by with the stock suspension with 285's and possibly 315's depending on what you're going to do with your truck. I feel as though I'm limited on where I can go with my stock suspension and would recommend at the very least a 1"-2.5" lift for 285,295,305's and a 3.5" lift of any combination for 35's.
 
Last edited:
I have the OME Heavies 850,863 and they rock.. Its a perfect lift for 285's and you can load the back full of stuff and it will sit perfectly level when you need it most.

IMHO if you get the shorter springs in the back for DD it will look level but when you load her up to hit the mtns or the beach it will ride low in the rear. Now isnt one of the reasons for the lift to reduce rear sag?

did you go with extended brake lines and a new rear panhard? or do you only need to do this if you add in the front and rear spacers?
 
Brian, if you want another educated opinion or have questions, give Christo a call at Slee Offroad. I just ordered my new suspension from him. He wants to know how you're going to be using the rig and what you want out of it, then he will recommend the best set up. For those of us with little experience lifting our own rigs, he is very helpful.
 
did you go with extended brake lines and a new rear panhard? or do you only need to do this if you add in the front and rear spacers?

No need to get anything else done except the control arm bushings. At full extension the brake lines have plenty of play in them. The panhard would beter align the axle with the body but its really not necessary (IMO).
 
Back
Top Bottom