LC80 "Explosive" Oil Leak?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 16, 2016
Threads
3
Messages
12
Location
Las Vegas, NV
Gents (and Ladies),
I've been searching around, trying to make an unnecessary purchase of an 80-series LC to supplement my 2014 JKU. Today I took a look at local offering. It ran well, and was remarkably rust free, but had a few significant leaks underneath. The most concerning is this big oil leak. I know oil leaks are tough to track down, and to some degree expected in an old vehicle, but it looks like it almost exploded out on this one (see oil on stabilizer bar in first image). Looks like a good bit has leaked out, though I couldn't see any active dripping, aside from the pooling visible in the photo. Anywho, the potentially explosive nature of it concerns me, just curious if any other have thoughts that would help.

IMG_20161213_105706301.webp


IMG_20161213_105713868.webp
 
80 series have 4 major oil leaks....

1. valve cover gasket
2. dizzy shaft o-ring
3. front crank seal
4. oil pump seal

indeed physical areas oil / wetness of are not necessarily correlated to the source of the leak...
am guessing you have #3 and or #4 oil leak

take a look at the top side of the skid plate - simply face your engine and look straight down
in the space behind you rad....should be bone dry.

if the top of the skid plate is "wet" chances are the front crank seal and oil pump seal need replacing.

most will advise that all four are baseline PM measures and indeed no more than :banana::banana: jobs to diy.
plenty of videos too to learn you some...

bF
 
80 series have 4 major oil leaks....

1. valve cover gasket
2. dizzy shaft o-ring
3. front crank seal
4. oil pump seal

indeed physical areas oil / wetness of are not necessarily correlated to the source of the leak...
am guessing you have #3 and or #4 oil leak

take a look at the top side of the skid plate - simply face your engine and look straight down
in the space behind you rad....should be bone dry.

if the top of the skid plate is "wet" chances are the front crank seal and oil pump seal need replacing.

most will advise that all four are baseline PM measures and indeed no more than :banana::banana: jobs to diy.
plenty of videos too to learn you some...

bF

Are these leaks specific to the 3FE or the 1FZ?
 
Thanks y'all for the prompt response. Sounds like you wouldn't necessarily consider these a dealbreaker, just something to be addressed.
 
Sumply a piece of cardboard under the engine bay, certainly no deal breaker when it comes to Cruizers...
 
With the amount oil on the bottom of the motor my vote is oil pump gasket.
 
So y'all don't think it's like a high-pressure spray or anything along those lines? That was my prime concern, since it was on the stabilizer bar. Trying to get used to the idea of "normal" oil leaks.
 
No, it's not like explosive diarrhea. It's more like insufficient bladder, or like an old guy that continues to piss on his shoes. It's normal as you age. Give it some Viagra and all the leaks stop.
 
Nope, just one or all of the big three. The oil pump cover gasket is probably the major culprit. You have to remove the harmonic balancer, so the crankshaft seal should then be replaced as it is probably leaking a little bit. The distributor o-ring is a simple job.

The valve cover, if leaking, is a simple job. Be sure to reseal the cam bolt half moons. This also gives you the opportunity to fully clean the throttle body and clean out the EGR ports.
 
What year is it? The 3FE is not "known" for the same leaks as the 1FZ-FE...

Oil leaks happen. Replace the gaskets or add more oil. Nothing alarming about these photos.
 
It's a 1994. 1FZ-FE. I gotta get used to oil leaks I suppose, just made a move on it, will probably pick it up tomorrow. I'll give it a good wipe down and start figuring out if it's worth the fix or if it'll just be adding oil for the duration. I figure, worst case, it's just an expensive lesson and a long walk through the Nevada desert. No biggie. I'll post pics once I get it squared away, thanks for the help y'all.
 
Rear crank seal is another source of leaks, but that tend to drip directly down and out of the bell housing. I have to agree about the lack of maintenance, that prop shaft UJ area looks as dry as a ducks arse under water.

regards

Dave
 
If you're new to 80's (and by your stats & this question, I'll assume so) -- if you have any buddies with an 80, drag him to every 80 you look at & buy him a beer for every time you don't buy.

Get a box of good ones for the day you bring one home one that you split while he helps you with a list of all the little crap that'll be your punchlist.

--I agree it looks like a main seal may be leaking, but a little continuous "blowdown" just means you pop the hood routinely (like you should anyhow getting to know your new to you used car) & see how much oil it uses. If you buy it, I'd take it to a coin-op car wash armed with 3-4 cans of degreaser and a sheet of cardboard to lay on. Hit it when warm, let soak then drop your tokens and clean the underside to start tracing the leak.

::If:: you have an 80 buddy, he'll earn a boatload of beers for help getting an example you want to continue putting money into.

Plus if you can get him to all the ones you look at, you can buy the good one before anyone else snakes it.
 
The oil pump cover seal, crankshaft seal, distributor seal are a 3-4 HR job. Pull the radiator at the same time to give you more room to work. You need to do a full coolant flush so may as well do it then. Replace your thermostat while you are at it. Check your fan clutch to make sure it spins but stops as soon as you stop forcing it to spin.

Then drive it likebyou stole it.

These motors are damn near bulletproof. But it is 22+ years old. It needs a little love and attention. Give it some and it will be strong for many years to come.
 
That's the anti-rust coating. Pretty sure mine is worse, I just need to top off the oil every few thousand miles. They usually look like they're leaking more than they actually are.

Replacing all the seals is an option, and I have been tempted to do it, but a quart of oil once or twice between changes is a lot cheaper and less time in the garage.
 
Yup, very likely a rear arch seal. Best way to handle leaks is to find a local place that does engine steam cleaning. Have them clean the engine top and bottom, then look for and repair leaks. Much faster, cleaner, and it makes an old truck a joy to work on. I have a local place and have had 4 of my vehicles there. Usually about $100 and worth every penny.

BTW, my rear arch seal was leaking (barely dripping, really) when I bought my '96 and it looked pretty similar to this truck. It's a bit of a pain to reseal, but not very difficult.
 
Back
Top Bottom