Just took my compression #s - 2F

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 10, 2005
Threads
58
Messages
224
Location
Belmont, NC
My cruiser didn't seem to have a lot of "guts" on the road at GSMTR last week (I've owned it 15 years now, but just went to the TBI over the past 4 years). Here are my #s. What do you think about them? I wish that #3 was a bit higher so that they would all be closer. Given the other #s is that more likely a wayward valve/set or rings? TIA.

#1 - 135
#2 - 128
#3 - 115
#4 - 125
#5 - 130
#6 - 130
 
How was the test done?

Did you adjust the valves before doing the test?


Did you try a wet test on the cylinders to see the increase in compression, if any?



Need more information......
 
Good point on the valve adjustment. Answer is no. I just got back from GSMTR and did a quick comp check. I'll adjust the valves and try it again tomorrow.

WHat is a wet test and how do I set that up?

Thanks.
 
Squirt about 1/2oz of oil in the cylider and retake the compression readings. If no change, probably a leaking valve, if it does change ^ then probably worn or broken rings. IIRC

Ed
 
a simple straw works well to get the oil in the cylinders
 
70chevfred said:
a simple straw works well to get the oil in the cylinders

Or an oil can;)

Ed
 
Poser said:
Oil cans...... ;)


Mmmmmm


:beer:


Pull the trigger....get a stream, lift up....one drop. Gotta love the Krauts;)
2F 021.webp
 
Diesel Wannabe said:
My cruiser didn't seem to have a lot of "guts" on the road at GSMTR last week (I've owned it 15 years now, but just went to the TBI over the past 4 years). Here are my #s. What do you think about them? I wish that #3 was a bit higher so that they would all be closer. Given the other #s is that more likely a wayward valve/set or rings? TIA.

#1 - 135
#2 - 128
#3 - 115
#4 - 125
#5 - 130
#6 - 130


Those are pretty good numbers. Not to worry. I have a '74 F motor and every cylinder is within 2# of 120 except number 5 which is 90#, and it did not change on the "wet test", so probably a valve. The motor runs smooth as a sewing machine.

Ed
 
Degnol said:
Pull the trigger....get a stream, lift up....one drop. Gotta love the Krauts;)


:grinpimp:
 
Compression came up pretty evenly, but even the dry #'s are OK. Your rings are probably worn. Does it use oil?

Ed
 
It doesn't use oil to the extent that I'd notice. I end up changing the oil every 2-300 miles as I rarely drive on road and the miles it gets are tough ones like at GSMTR...
 
With nice even numbers like that, I would not worry about it.

GL

Ed
 
Do you think I would notice a significant reduction in top-end power at this level of compression? If not, I need to keep hunting for why I don't have the "guts" that used to be there. I used to run 70mph on the interstate pretty easily and actually towed a trailer behind this 40 from Indiana to GSMTR twice and was able to run 65 easily (ran a Weber 38 back then). Now I don't have much top end and I'm running a TBI and DUI HEI...
 
are you using a generic prom or a custom burnt one?



Get some more fuel into the engine.... ;)


Oh wait....don't do that, then we will get the " how come my mileage sux " thread... :)



:beer:
 
I am not a 'computer guy', but have been told that there is a way to set up a lap top and have it talk with the computer that is running your engine, and that it will run a program that will verify your parameters, and tell you where you need to adjust them, and then you can burn a new chip according to your needs, and increase the performance.


I have not done any of this my self yet, but it will be happening in the not so distant future after I get the hardware/software and get a 2F set up with TBI.


Most generic operating chips are tuned lean to very lean...

:beer:
 
Back
Top Bottom