JDM tools space

[JerryLX450]

Does anybody know where can i get them? Is it hard to install it? Sadly speaking the U.S 80series landcruiser didnt came with it.Sometimes when i go wheeling and hit something the tools bag just loose not in place.

Jerry

 

[mot]

Jerry,

Do you mean the space where the tool bag goes?
Does the US-spec 80 not have that space???

I've taken some pics of the area when I did the 2nd-row seatbelt mod, but can't recall anything out of the ordinary when looking at the attached pics. Are those of your rig or of a JDM one?

Sorry if I'm a little dense!

Mot

Does anybody know where can i get them? Is it hard to install it? Sadly speaking the U.S 80series landcruiser didnt came with it.Sometimes when i go wheeling and hit something the tools bag just loose not in place.

Jerry

 

[JerryLX450]

Those are JDM one and just took this pic of my rig.It's very poor design for U.S version If it's not too expensive can you help Mot?

Jerry,
Are those of your rig or of a JDM one?


Mot

 

[psfpilot]

Mott,
I think he's looking for that black plastic piece that the tools are resting against in the first set of photos.

Jerry,
Check Cruiserdan's ROTW, I think it mentions how he procured that part.

 

[JerryLX450]

Mott,
I think he's looking for that black plastic piece that the tools are resting against in the first set of photos.

Yes Psfpilot right i'm looking for the black plastic piece.

 

[97 FZJ80]

I got mine from CDan. Be sure to order the screws to mount the cubby to the body.

 

[Rich]

Jerry, you are supposed to use the rubber strap that secures the factory jack to hold the tool bag to the same.

I don't think the black plastic add on is intended to hold the tool bag, not to say that it can't be stuffed in there.

 

[firetruck41]

Jerry, you are supposed to use the rubber strap that secures the factory jack to hold the tool bag to the same.

I don't think the black plastic add on is intended to hold the tool bag, not to say that it can't be stuffed in there.

That's what I do too, just put the bag on top of the jack, and then use the black rubber strap to secure them both in place, no problems.

 

[cruiserdan]

The photos in post #1 are of my vehicle.

I can supply the sleeve.

 

[mot]

Those are JDM one and just took this pic of my rig.It's very poor design for U.S version If it's not too expensive can you help Mot?

Jerry,

Looks like Cdan will be able to come through for you on this one!

Good luck!

Mot

 

[PHAEDRUS]

You just need to stuff more s***e in there,
mine has a pair of gloves, the tool bag, a roll of duct tape, bottle of brake fluid, quart of oil, a 5x8 tarp folded up and roll of shop towells. no rattles.
Dave

 

[Beowulf]

You just need to stuff more s***e in there,
mine has a pair of gloves, the tool bag, a roll of duct tape, bottle of brake fluid, quart of oil, a 5x8 tarp folded up and roll of shop towells. no rattles.
Dave

Sounds like mine 'cept you forgot the jumper cables, red shop rags, wheel lock key, and XXL surgical jump suit in case you have to change a tyre while on the way to a job interview.

-B-

 

[MDarius]

...and the signal flares and tire repair kit, the small tool kit for sockets, vice grips, etc., a couple pieces of candy from the kids, and I think you nailed it. I aint got no room for a plastic sleeve!!

 

[PHAEDRUS]

Nah -B-
You need to have the tote in the back with the jumpers and tow straps and ponchos and emergency blanket, first aid kit and some more oil and atf.
Dave