Is my front diff to shiny?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

For the life of me I cannot understand why one would spend the time and effort doing something so pointless as to to polish an axle housing to this degree and then paint it.... and not turn the knuckles with a SOA. Let us know how it tracks and flat towes with -5* caster. If you do drive this on the road I am glad you're 2000 miles from my wife and kids. To each his own! :confused:
 
just so you know, he did not actualy polish it, its just cleaned really well.
adn i have no idea on why no cut and turn.
Shane

dgangle said:
For the life of me I cannot understand why one would spend the time and effort doing something so pointless as to to polish an axle housing to this degree and then paint it.... and not turn the knuckles with a SOA. Let us know how it tracks and flat towes with -5* caster. If you do drive this on the road I am glad you're 2000 miles from my wife and kids. To each his own! :confused:
 
Your right, too each his own. :)

The cruiser spends most of it's time traveling on the road, on a trailer. I own it for fun and going off road. I have a car and a truck for daily driving.

At this time I have about 6" to 8" of lift on it with out having the cut and turn and turn done. The Skyjacker springs come with a built in tilt to the pinion. All I have done was to match this tilt. It tracks just fine on the road, I have done 55 on the state HW and only needed 1 hand on the wheel. If I have problems after the SOA, I will most likely purcase one of the housings I have seen advertised on here that has been cut and turned. Cutting and turning was a job I didn't want to tackle at this time. :)


dgangle said:
For the life of me I cannot understand why one would spend the time and effort doing something so pointless as to to polish an axle housing to this degree and then paint it.... and not turn the knuckles with a SOA. Let us know how it tracks and flat towes with -5* caster. If you do drive this on the road I am glad you're 2000 miles from my wife and kids. To each his own! :confused:
 
G_Stratton said:
Almost%20Finished%2011.JPG
Sure does look pretty - now go bash it on a rock quick!

:cheers:

Tucker
 
What kind of disk set up is that? I have a 68 with drums, I've aquired a dual master cylinder and brake booster and would like to disk the front one day. But they are expensive, but worth the money, just wonderin if you found a cheaper way to go. Thanks
 
The cut and turn is not that hard. I was very intimidated by all the pictures I have seen with a guy and a big ass rosebud torch and a huge pry bar...yikes. Jeramiah Proffit talked me into doing it myself and it was easy. All you need is a $15 angle finder from Home Debit, 4-6"90 deg angle grinder and a bunch of grinding wheels. Oh, and a welder. I did all the cutting and grinding on sawhorses to save my back, put the axle back in, tightened Ubolts and put a hammer handle through the trunion bearing holes. Tap the handle with another hammer until you get the desired readings, tack, remove, weld up, clean up, resinstall and you're done. This solves sooo many problems.
 
CruisinTiger said:
What kind of disk set up is that? I have a 68 with drums, I've aquired a dual master cylinder and brake booster and would like to disk the front one day. But they are expensive, but worth the money, just wonderin if you found a cheaper way to go. Thanks

Minitruck, I traided one friend a trany for the Minitruck axle. From another friend, I aquired the front axle from a 69 Cruiser for the rest of it. I rebuilt the knuckles and breaks, and put new seals in the axle. I think total cash, I have about $400 into it including the Aussie Locker.

You have the same problem I had. Your 68 has the front end with ball and claw instead of Birfields. You will need to aquire a 69 or newer front cruiser axle.
 
Back
Top Bottom