In consistent clutch pedal

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 26, 2007
Threads
178
Messages
1,036
I'm getting inconsistent clutch pedal each time it is pressed. Sometimes there is full pressure all the way down and sometimes nothing until almost to the firewall. I replaced the master about a year ago and I've bled it again, no leaks at the slave or anywhere else. Could it be the master has failed already? It was a new aisin master.
 
Landcruiser clutches can usually be gravity bled. I’ll attach a clear line from the slave bleeder and run it down into a bottle. Then remove the cap of the clutch master and top it up with suitable brake fluid. Open the bleader valve and it should start to flow. Keep adding more fluid till it flows clear and bubble free. Sometimes air leaks past the bleeder threads... if this is the case, don’t worry about a few bubbles, just run it till it looks like new fluid.

Sometimes I’ll close the valve, pump it a few times and bleed it some more.

I’d flush it and check out the results before replacing anything. That said, something likely needs to be replaced. The slave would be my best guess. Slaves and masters are usually replaced together. If it’s pulling in air on the return stroke, it would l lead to inconsistent performance. I’ve consistently got 10 years out of rebuilding my master... it’s less likely a year old ASIAN one is the source of trouble.
 
Thanks very much for the video. The reverse bleeding method is aces for all new components.

I did not consider the air getting sucked in because it was not leaking fluid there but I understand air is easier to get past the seal than fluid.

Good question when the "new" master was really new, didn't think about that. In my mind the master is not moving a consistent amount of fluid each time. I can see air giving me a soft pedal but it should be consistent.

Thanks to those how offered suggestions.
 
I have had good luck with gravity bleed on TC clutch.
A trick with many clutch and brake master cylinders is when bench bleeding, tilt the front of the master cylinder slightly up and pump some fluid through being sure you do not empty the reservoir.
This will help release any trapped air in the cylinder.
 
Finally got a day off. I did the gravity bleed yesterday and it seems to have fixed it for now. I'll keep you posted.
 
I occasionally had this for years. My cause appeared to be an incorrect combination of early and later year clutch parts. In your signature it appears you have a 3FE. Are you using the earlier or later clutch setup?

My solution was to assemble everything from the same years: Mixing clutch slave parts from different years
 
I am having the exact same issue. Replaced master, slave, and rubber hose about a year ago and have had zero issue until about 2 months ago. Usually have to pump the clutch pedal while I am driving to keep it firm. If I don't, the pedal will go to the floor almost and have only about 2 inches of travel vs the normal. I have flushed and bled the whole system multiple times and made sure everything was tight. I am replacing the master cylinder today so hopefully that will fix the issue
 
I've had the same issue multiple times in the past. Sometimes the clutch is there, and sometimes it's not. In my experience, I have to eventually replace master. I always keep a spare master and slave on the shelf and replace whatever component has gone bad at that time. Usually if the slave goes bad, it never comes back and fluid is on the ground.
 
Replaced my master yesterday and so far everything is working normally. Drove it around for about an hour with zero issue
 
I'm getting inconsistent clutch pedal each time it is pressed. Sometimes there is full pressure all the way down and sometimes nothing until almost to the firewall. I replaced the master about a year ago and I've bled it again, no leaks at the slave or anywhere else. Could it be the master has failed already? It was a new aisin master.

Just noticing your handle. Do you run a V8? I have a Mark's conversion kit and have always had trouble with mine with the exact issue. Does your TO bearing clip on with both clips? Mine doesn't, and I got some advice recently that suggested this will cause an intermittent loss of free play because the bearing isn't square to the pressure plate. The result is that at times the clutch feels good and other times it doesn't. I'm yet to check this on my own truck but the theory is sound.
 
Just noticing your handle. Do you run a V8? I have a Mark's conversion kit and have always had trouble with mine with the exact issue. Does your TO bearing clip on with both clips? Mine doesn't, and I got some advice recently that suggested this will cause an intermittent loss of free play because the bearing isn't square to the pressure plate. The result is that at times the clutch feels good and other times it doesn't. I'm yet to check this on my own truck but the theory is sound.

I used to have a v8 but it is now a 3fe running the standard 4/5 speed clutch setup. I will try to check the TO bearing clips also, Don't know if I can see it without pulling the transmission. It worked fine for a few years then last year I suddenly had no clutch so I replaced the master. Now a year later I am getting this.
 
I am having the exact same issue. Replaced master, slave, and rubber hose about a year ago and have had zero issue until about 2 months ago. Usually have to pump the clutch pedal while I am driving to keep it firm. If I don't, the pedal will go to the floor almost and have only about 2 inches of travel vs the normal. I have flushed and bled the whole system multiple times and made sure everything was tight. I am replacing the master cylinder today so hopefully that will fix the issue

If I push the clutch full to the floor each time it is more consistent (better). That's why it felt better when testing after the bleeding. If I drive lazy as usual I can lose the clutch pedal almost completely if clutching a lot. If It is a while between clutching then it seems to recover on its own. Maybe some internal port clogged?
 
Typically, it is recommended on here to replace both the slave and the master together if they are old.
 
Not sure if you got this fixed, but my problems are back after replacing both the master and slave. It felt great for like an afternoon and now the pedal has about 2 inches of resistance in it. Going to circle back and try to adjust per the FSM again....
Hope you had better luck
 
I replaced the master and that seems to have fixed it. I did however see some minor leakage at the slave this time so am waiting for that to arrive. I hope that fixes it because all that's left after that is not good.
 
Typically, it is recommended on here to replace both the slave and the master together if they are old.

good advice.

After replacing the slave I am back to normal. I did find however that the rounded part of the rod that fits in the arm was really crammed in there and there was no pivoting. It may have been an incorrect part. The new one that came with the new slave fit better and now pivots. Clutch is also easier to push in.
 
Back
Top Bottom