Identifying a lift

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 11, 2009
Threads
15
Messages
125
Location
Denver, CO
I'm considering purchasing another 80 I found. The Owner has very little knowledge of the work that was done. It has a 6" lift and a SC. I know that anything above 3" starts to get pricey, and if not done right, it can make it fairly undrivable. I don't recognize the lift, and hoped someone else might. Also, it looks like the under body has been almost chemically cleaned....putting up a few red flags. Does this look solid? Any idea what an underbody would look like this? Any help would be greatly appreciated!

Movies here:
‪LC‬‏ - Google Drive
 
Looks homemade. You can see square section steel lift blocks up front, and it looks like a braced extension for the rear track bar.

20180103142256-5d1d7594.png


20180103142253-44dbf207-me.png


As for whether it's done right... Dunno. Ask @nukegoat.
 
I had guessed it might be with that tubing, as I had never seen a commercial lift like that before....Guessing the front drive line angle will be an issue, as well as front control arms? Any ideas on the odd wear on the undercarriage? (shiny, with light rust coating? is that evidence of wheeling a lot in the sand???)
 
Lowering the rear track bar mount at the frame is safe/fine as long as it's braced appropriately. I can't tell if it is. Lowering radius arms at the frame is also benign as far as geometric impact. What you wouldn't want to see is arbitrary alterations to the front track bar since it would create bump steer.

Honestly though it looks kinda ghetto/hack. I would walk
 
Eh. Driveline angle may or may not be an issue. Spacing the arms down like that negates, what, two inches of lift? (I'm purely guessing that's 2x2 steel). Whoever did the lift may have done a cut-and-turn. You'd just have to get an angle finder on it and see what the caster is.

I didn't see the wear on the undercarriage (those videos are a PITA to open), but it looks like quite a bit of rust and I find it odd that the modifications don't seem to be painted. At least you can inspect the weld quality, I guess. It looks like you can remove most of the modifications, so if it's reasonably priced and runs well...
 
under 200K with a SC and locked for $11.5K. sorry the videos are a pain, I thought you could just click and play....They were too large to upload here. Seems a lot or places are shiny, almost like they were sandblasted. I was told the truck was from Hawaii....
 
If those mods were all bolted on and the rest of the cruiser was clean I'd consider it. The lift would certainly not be a selling point for me as it looks a little ghetto, like nukegoat said.
 
Yea it's been for sale for long time maybe year or little less, started at 20k, my buddy is looking at and knows cruisers and this guy wouldn't tell him much, he walked from it. Guy also told him 13k was his low, didn't sound like he knew much mechanically and that's when he turned into douche on my friend, didn't sound like it was worth what he was wanting, and considering you would be redoing the lift I wouldn't offer his price overpriced in my opinion. Looks rusty in your pics
 
Just drive it down the interstate at 85 mph and if your not scared, and there are no vibrations then buy it.
 
It's a 3.5 hour drive for me to even look at it...@ajax1, did your friend put eyes on it, or just ask questions over text/phone?. Owner was a bit douchy to me as well...but thought it might be worth it as the body looks clean. Would you friend have any additional info from his inspection?
 
Maybey dont buy it those home made radius arm drop brackets look like they got some booger welds on them.
 
My buddy got pissed off since guy was being a douche and it was hack job and overpriced he lives in Denver also, I wouldn't bother unless you really dig it, for that kinda cash there is much better close to you in Denver, he has looked at some that were lower miles less coin like 7 k with clean body good paint interior with 175k miles. I would walk unless you can get for round 7 your gonna be baselining and buying new lift . There is a reason it hasn't sold yet it's been listed along time and started at 20k when I first saw it.
 
A 6 inch home made lift is probably not a good idea. These rigs don't do so well in roll overs and you don't want a claims adjuster denying a claim because of a sketchy lift. Especially if someone get hurt.
 
The value was the SC, low (ish) miles, factory lockers and clean body. I would probably remove the lift and install a decent 4"...but hard to make a judgement without seeing it first hand.
 
Why someone would even take the time to try to "build" a life for one of these since they are readily available for $1000 or less. A hack job is ALWAYS harder to undo than to buy a truck without a lift and add one.

Yeah, it has a SC.

Buy one without for a LOT less, add a turbo, ARB Air Lockers, and a 4" lift of your choice and you'll be money ahead as well as you'll know more about the truck and do it your way instead.

I'd walk from it because of the homemade lift.
 
Back
Top Bottom