I know, I'm sorry

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 16, 2014
Threads
51
Messages
772
Location
Union, Ky
I know that there are several threads on this that I've looked at, but I just can't for the life of me get the distributor right... I took it apart to replace the o ring and scratched marks where it was, but I cannot get it running. I turned the pulley to 0 and put the gear 15° ahead of the line on the distributor like the threads said and the rotor is roughly 11 o'clock. The ignition wires and little plug thing are all connected. But no matter what I have tried including following the fsm and other websites i cannot not get it to run. Any help is appreciated.
 
You may not have been at TDC of the firing stroke when you put the distributor in. You can rotate the engine 360 deg and put the distributor in again. Follow the FSM exactly when inserting the distributor.
 
You may not have been at TDC of the firing stroke when you put the distributor in. You can rotate the engine 360 deg and put the distributor in again. Follow the FSM exactly when inserting the distributor.[/QUOTE
Thanks, but I tried that several times
 
I did that several times and I read that the rotor was supposed to be leaving the #1 cylinder at 0
 
Was it running good before you removed the distributor? Does it try to fire when you turn the key or does it just crank over without trying to start?
 
Just finished doing this about an hour ago. Tried at tdc but it still didn't work amd I was following the fsm. Was advised to rotate 360 degrees and try again. The mark passed with about a quarter rotation so I kept going for a full rotation. Lined up the marks and boom!
 
Was it running good before you removed the distributor? Does it try to fire when you turn the key or does it just crank over without trying to start?
Yes, I only messed with it because it was leaking a little oil. It's trying, I got it to run once for a few seconds and the there black smoke. It seems close sometimes...
 
Just finished doing this about an hour ago. Tried at tdc but it still didn't work amd I was following the fsm. Was advised to rotate 360 degrees and try again. The mark passed with about a quarter rotation so I kept going for a full rotation. Lined up the marks and boom!
Does it mess the timing up if you turn the crank the wrong way?
 
I turned it counter clockwise when i was lining up the cams but then I saw in the fsm to "always turn the crank clockwise". I only turned it clockwise from there.
 
I turned it counter clockwise when i was lining up the cams but then I saw in the fsm to "always turn the crank clockwise". I only turned it clockwise from there.
Alright, I may try aligning the crank just turning clockwise.
 
The manual may say to turn it clockwise only but that's not because turning it the opposite direction will throw the timing off. The important thing is that you are at top dead center on the firing stroke not the exhaust stroke.
 
The manual may say to turn it clockwise only but that's not because turning it the opposite direction will throw the timing off. The important thing is that you are at top dead center on the firing stroke not the exhaust stroke.
You can tell the stroke by the rotor position right? 11 is firing, 5 exaust?
 
. Now that you have turned the engine since pulling the distributor all you can do is try it at 0 degrees. If it won't start, rotate 360 degrees and put the distributor in again. It may be necessary to pull the valve cover so you can see where the cam shafts are.
 
Last edited:
NO! The camshaft rotates once for every two rotations of the crankshaft. The piston can be at TDC for the compression stroke, or for the exhaust stroke. Just follow baldilocks advice above.
Oh, thank you all!
 
Well it's been an hour and we're breathless with anticipation.....
 
Well it's been an hour and we're breathless with anticipation.....
I'm out working on a community park but I will let you know before noon! haha
 
So is 15° on the distributor about how many splines on the gear? Or should I go by the little ticks? I was doing 2-3 ticks ahead of the line.
 
Line up the line on the pully at tdc/0

There is a protruding mark on the gear. Line it up with the mark/line on the shaft of the distributor. Insert the distributor so that the hold down bolt is in the middle of the adjustment slot.

If it doesn't start. Remove and rotate crank 360 degrees and try again.
 
Back
Top Bottom