Howling/Buzzing noise help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 11, 2017
Threads
11
Messages
72
Location
Birmingham, AL
So my 80 makes this howling noise above ~30mph but only when my foot is on the accelerator. It gets louder the faster I go. From my searching on here, I assume that it is likely the differential bearings or the u joints that need to be greased. I am going to grease the joints tomorrow and see if that helps. Does anyone know of any mechanics in the Birmingham area that could do this work? Or is there anyone that local that would be willing to help for beer or $?
 
Could be tons of stuff. You should give more information, like what year it is, what condition it's in (lifted?), and what maintenance has been done (Birfields greased?).
 
It is a locked 95. I got it at the end of July and here is everything that has been done to it since I got it.

7-29-17

128,250 mi
Rear differential fluid change
Front differential fluid change
Transfer case fluid change
Transmission fluid change
Oil and filter change
New windshield wipers
Front end alignment
New tires
New battery
Radiator flush with new coolant and distilled water
Drive belts replaced
Thermostat replaced

This above was all done by the PO who is on mud.
I had it shipped the next day.

8-5-17
Removed running boards

8-15-17
129,100 mi
Front axel service with Front bearings, brake pads, and rotors replaced
Rear bearings, brake pads, and rotors replaced

8-16-17
Rear hatch gas struts replaced
New high and low headlights

9-30-17
Removed factory roof rack

10-4-17
130,225 mi
New Aisin blue hub fan clutch
New Denso air filter

10-5-17
130,333 mi
New Denso Pt spark plugs
New NGK spark plug wires
New Beck Arnley distributor cap
New Beck Arnley ignition rotor
Bypassed rear heater

This problem has been persistent since I got it. At first I assumed it might be the wheel bearings so I had front axel serviced. Mechanic also replaced the rear bearings for me as well.
After it continued I thought it might could be the fan clutch, and my mechanic verified that it needed to be replaced so I did that and the spark plugs because it was starting to missfire. But the problem still persists and I now believe that it could be the diff bearings.
 
Did the U-joint grease solve the problem? Can you tell if the sound is in the general area of the passenger floorboard?
 
Greasing didn't help any. I greased all the u joints and both drive shafts. Had it over at my uncle's for a late Thanksgiving dinner Friday evening and since he is a mechanic had him take it for a spin to see what he thought the noise was. He said it was a bearing on the rear diff that had gone bad.
 
Before you tear into the differential, put it up on jackstands and put it in gear. This will remove all the non-drivetrain noise.

If you really have an input bearing failing, you should be able to remove the rear end of the rear driveshaft and wiggle the pinion input. If it doesn't move, I'd put tearing into it somewhere near the bottom of the list. Also, drain the oil and strain it through a couple of coffee filters. If it's clean, it's probably not the differential. It's hard to run a pinion without a good bearing and not grind the teeth.

That's not to say you can't have clearance related noise, but again, I'd put it near the bottom of the list.

I have a similar problem with my '94, which is currently vacationing at UA. If you determine it's a differential problem, and find a shop you trust, I'd be interested in knowing who you find. Just in case, because I can't really get to Tuscaloosa in a hurry.
 
Had it over at my uncle's for a late Thanksgiving dinner Friday evening and since he is a mechanic had him take it for a spin to see what he thought the noise was. He said it was a bearing on the rear diff that had gone bad.

Maybe he's right, maybe he's not.

My howl/whine sure sounded like it was from the center or rear. Locked the center, removed the rear DS and went for a drive. Noise still present and unchanged.

Rinsed/repeat with front DS removed instead. Noise 100% gone.
 
If you determine it's a differential problem, and find a shop you trust, I'd be interested in knowing who you find. Just in case, because I can't really get to Tuscaloosa in a hurry.

Will do!

Maybe he's right, maybe he's not.

My howl/whine sure sounded like it was from the center or rear. Locked the center, removed the rear DS and went for a drive. Noise still present and unchanged.

Rinsed/repeat with front DS removed instead. Noise 100% gone.

So all I need to do is pull the driveshaft with the CDL locked to isolate the noise? No need to pull the corresponding diff as well?
 
It’s fairly easy to diagnose if it is the u joints. It isn’t difficult to remove the front drive shaft and drive in rear wheel drive only and vice versa.

Have you done the pin 7 mod? If you have it is really simple to lock the center diff then remove the front shaft, drive, see if the noise goes away.

If you don't have the pin 7 mod, do it. But you can also lock the center diff by putting it in low, drive a few feet so it engages, then pull the CDL fuse, switch back in to 4hi, remove the front drive shaft (or rear drive shaft).

Make sure you mark the drive shaft and flange so that you get it lined up properly when you reinstall...
 
Also, one word of caution when driving in front wheel drive or rear wheel drive. It is different than full time 4wd.
 
These guys are sharp! Remove the front DS, lock the CDL and drive, if sound persist then reinstall front DS and remove rear DS lock CDL and drive. This will help you isolate which side the issues is on.

Now when you remove these DS inspect the U-joints and splines. Inspect the U joints by trying to find play in the joints, hold the u joints so they are in a X Y axis, apply force back and forth along the X axis and then the Y axis if there is any play this is wear that isn't good and could cause vibrations. Inspect the splines by holding each side of the spline and twist by hand back and forth, if there is a noticeable click back and forth this can cause drive line clunk and howl.
 
I had this issue when I first got my truck too. I did the methods described above, it was the front diff input bearing going bad and allowing in and out movement. so when you remove the driveshafts grab the diff input flanges and push pull on them there should be no movement.
edit to add: the PO had not fixed a front axle seal leak and drove for who knows how long with no gear oil in the axle. It had no oil when I bought it.
 
I will add that most likely the i joints are in need of replacement. They are pretty cheap to replace. As much as I don’t like throwing parts at a problem I would plan on replacing them while you have the drive shafts out. Peace of mind for down the road.
 
So today I finally had time to remove the front DS. Took way longer than it should have for only 8 bolts... U joints seemed to be in good shape when I got it out. Drove it around with the CDL locked and the sound persisted. While driving down a long hill, I shifted into N and the sound went away. I assume this means that it is the rear diff that is the issue? When I get a chance to get under it again, I am going to reinstall the front DS and then remove the rear.
 
Okay pulled the rear DS today and put the front back in. When I took it for a spin the noise persisted unchanged. I managed to get a video this time though. So maybe that will help y’all figure it out. When shifting into neutral, the sound still went away. Any ideas what could be up?
 
Back
Top Bottom