HOT PS floor pan area

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 5, 2006
Threads
127
Messages
745
Does anyone else notice that on warm days the PS floor pan area gets very hot, even the carpet is warm to the touch?

Does this have anything to do with exhaust manifold?? time to replace exhaust piping? maybe upsize to 2.5 or 3" to match the SC?

Curious if anyone else has noticed this... as i have had passengers complain of seriously cooked toes..
 
I just fixed this same problem on mine. Even though my cats are gone, I was still getting a ton of heat there. Enough in fact that my :princess: would complain on trips over an hour that her feet were cooking. Last month I installed two layers of Damplifier Pro and Luxury Liner Pro from 2nd Skin on the floor. I would say it helped shield some of the heat, but not much. Yesterday I removed the heat shields and put a layer of Damplifier Pro on the underside of the floor and then reinstalled the heat shields. Tonight I drove to Tucson and back (about 3.5 hours) in 105+ heat. The passenger floor was the same temp as the driver side!

Here are some pics of the shiny Damplifier Pro and the exhaust for reference:

DSCF6020.jpg


DSCF6021.jpg


DSCF6022.jpg


DSCF6023.jpg
 
Last edited:
I think all 80's have this problem, most of us don't worry about it unless :princess: complains, no?

Gotmud, do you think the final solution, insulation BEFORE the floor sheetmetal made the biggest difference? Or would you recommend the ENTIRE solution that you did to solve the issue?

I would believe that preventing the heat from getting to the sheetmetal under the carpet eliminates most of the heat. If you insulate between the carpet and the sheetmetal, you're just trapping the heat and it eventually gets the carpet hot, just might delay the inevitable but happens still.

Also, how confident are you in the adhesion of the layer of damplifier pro to the underside? Did you use any mechanical means of attaching it or is the adhesive on the stuff good enough? No experience with Damplifier, so may be an ignorant question.

This is is on my B list. It was on the A list until we got a minivan as the family truckster!


Dan.
 
I am a big believer in putting it on the inside. Though it didn't keep out as much heat as I wanted, it did make a HUGE difference with sound. As for putting it on the bottom side, I removed my heat shields and scrubbed the area with Purple Power and rinsed. Next I sprayed the area down with Brakleen. Once dry I placed the Damplifier Pro on the floor board. This stuff will stick to just about anything! Once it was installed, I replaced the heat shields, sandwiching the Damplifier Pro between the floor and shields. I'm confident it will stay put. If I lived in a wet climate, I might have sprayed it with undercoating before replacing the heat shields. You might check with Ant (aka second skin rep) and see what he says about covering up the damplifier with some type of sealer for non-desert areas.
 
I insulated under the carpet with a layer of foil backed closed cell foam 10mm thick and a layer of aircell thermal insulation (like foil coated bubble wrap). It amde a big difference to the heat and noise transfer.
The biggest difference came from insulating around and inside the gear shifter, lots of heat was coming up through there.

I like the idea of the insulation under the cab :cool:
 
I put three layers of Damplifier Pro around the tranny tunnel (inside) and it helped with the heat and noise. Again, mainly the noise. The only "hot spot" left is the cubby in front of the arm rest. Actually the cubby is fine, but the bolt that screws in the floor is f'ing hot.
 
Last edited:
Second Skin's Firewall is what I plan on using on the outside of the floor pan for my truck, and should work just about perfectly.

It's designed in mind with external applications as well, unlike the Damplifier.
 
Could always just use some header wrap on the exhaust pipes before/after the cat's. That should help a great deal.
 
Its time to flush the transmission,pull the pan and clean its filter.These 62s and 80s get very hot if not taken apart and filters cleaned and flushed well; no rodney flush. 2 cents Mike
 
Could always just use some header wrap on the exhaust pipes before/after the cat's. That should help a great deal.


Header wrap is a great way to start your truck on fire, or rust components out.
 
Simply physics dictates that insulation under the sheetmetal floor would give the biggest bang for the buck. As noted above, reflecting the heat from ever getting into the floor is best. Watch out for header wraps as they can trap moisture/salt on the pipes and accelerate rust.

Having said that, my bro in law simply put a shaped piece of 1/4 inch plywood under his passenger floor mat for a cheap/fast solution that made his wife happy.

DougM
 
Could always just use some header wrap on the exhaust pipes before/after the cat's. That should help a great deal.

Header wrap is a great way to start your truck on fire, or rust components out.

...and adds too much heat to the cat. They'll overheat too if too much heat goes into them. Key is to keep the heat that comes off the exhaust from heating up the sheetmetal.

The PS of the engine room seems to be where most of the heat is and the main path for it to exit the engine room is down below the PS footwell. I wonder if those who have put hood vents in strategic places have noticed a big difference in footwell heat?

Dan.
 
...I wonder if those who have put hood vents in strategic places have noticed a big difference in footwell heat?

Dan.

That's my next step. I recently tried to order the louver vents from a 94-96 Grand Prix GTP hood that seem to work well. GM quit making them:frown:

I know other vents exist, but most I have seen require rivets to secure them to the hood.
 
Second Skin's Firewall is what I plan on using on the outside of the floor pan for my truck, and should work just about perfectly.

It's designed in mind with external applications as well, unlike the Damplifier.

Firewall is a good product but if you can wait another 2 weeks, we are getting ready to launch our newest thermal insulator.
it is a 3 part system with an ultra high ehat rating.

It can take the heat from 1200 degree headers and turn it in to about 95 degrees.
This would go on the exterior side of the vehicle to prevent the heat from coming through. Then if you weanted to do an all out amazing job, use Damplifier Pro on the interior sheet metal, then a barrier like Luxury Liner Pro or heat Wave Pro on top.

That would be amazing!

Hope that helps
ANT
 
Header wrap is a great way to start your truck on fire, or rust components out.

Aren't the OEM pipes stainless? They shouldn't rust with header wrap if they are. Also, if the cat's are left open to the air there shouldnt be any fire hazard when using header wrap, simply wrapping the pipes is what I was referring to. The main risk of using header wrap from my experience is (1) moisture getting trapped in the wrap and causing rust when your pipes are not stainless, and (2) cracking at the welds, because when tightly wrapped header wrap will not allow the metal to expand contract as it usually does and may lead to premature cracking at the welds and stress points.

With all that said, I think the best longterm solution would be (1) to make a 2 layered heatshield to place in between the catalytic convertors and the floorpan, and (2) to ceramic coat the pipes to keep heat in better. A little pricey to ceramic coat it all, but well worth it if you're going to do it right.
 
Firewall is a good product but if you can wait another 2 weeks, we are getting ready to launch our newest thermal insulator.
it is a 3 part system with an ultra high ehat rating.

It can take the heat from 1200 degree headers and turn it in to about 95 degrees.
This would go on the exterior side of the vehicle to prevent the heat from coming through. Then if you weanted to do an all out amazing job, use Damplifier Pro on the interior sheet metal, then a barrier like Luxury Liner Pro or heat Wave Pro on top.

That would be amazing!

Hope that helps
ANT

That sounds fantastic! Is it a product like Spectrum/Firewall, or something more like Damplifier? We need details. ;p


Aren't the OEM pipes stainless? They shouldn't rust with header wrap if they are. Also, if the cat's are left open to the air there shouldnt be any fire hazard when using header wrap, simply wrapping the pipes is what I was referring to. The main risk of using header wrap from my experience is (1) moisture getting trapped in the wrap and causing rust when your pipes are not stainless, and (2) cracking at the welds, because when tightly wrapped header wrap will not allow the metal to expand contract as it usually does and may lead to premature cracking at the welds and stress points.

Stainless can and will rust. It takes much longer, and is much more resistant, but it will eventually rust through. Having standing water laying against it will accelerate the process.

Granted, high quality stainless will rust much slower than the cheap stuff they just coat and then call stainless, but it'll happen eventually. Additionally if mild steel (or particles from mild steel) get onto the stainless, it will cause it to rust. (Which is why you don't let your stainless steel knives touch the mild steel ones when you're washing them in the dishwasher. Else you get spots of rust on your stainless steel knives.)

The fire danger is from the wrap absorbing oil, etc over time. Eventually it will become saturated, and then becomes an extreme hazard. My pops has been out on many car fires that have been caused by header wrap.

Ceramic coating would be the way to go, but it's $$$.
 
i used the adhesive thermal blankets and applied over the factory heat shields as gotmud did. i think there was one above the downpipe, and over the cats. i had plenty left over, so i peeled back the carpet along the passenger footwell and lined that also. the passenger side of the tranny tunnel also got some. i had enough to double up on the layers...and it worked great. no more :princess: complaining about hot feet. too bad the whole tranny tunnel wasnt accessible since id also want to line that. things that go in the little cubby hole and center console tend to get warm as well...so dont put any chocolate in there!
 
That sounds fantastic! Is it a product like Spectrum/Firewall, or something more like Damplifier? We need details. ;p




Stainless can and will rust. It takes much longer, and is much more resistant, but it will eventually rust through. Having standing water laying against it will accelerate the process.

Granted, high quality stainless will rust much slower than the cheap stuff they just coat and then call stainless, but it'll happen eventually. Additionally if mild steel (or particles from mild steel) get onto the stainless, it will cause it to rust. (Which is why you don't let your stainless steel knives touch the mild steel ones when you're washing them in the dishwasher. Else you get spots of rust on your stainless steel knives.)

The fire danger is from the wrap absorbing oil, etc over time. Eventually it will become saturated, and then becomes an extreme hazard. My pops has been out on many car fires that have been caused by header wrap.

Ceramic coating would be the way to go, but it's $$$.

Ah, oil. I wasn't thinking of that. Yup, if you've got oil soaked wrap that would start a fire very easily.
 
Back
Top Bottom