High and Low beams at same time?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 22, 2004
Threads
204
Messages
11,638
Location
Deep East Texas
I did a half hearted search, but I guess I missed it.

Can the 80's headlights be wired such that the low beams also come on with the high beams?

The high beams are pretty darn good....and I'm getting ready to replace the low beams (which suck) with the 9012 bulbs, but....we live in the country off of a very dark and winding F.M. road, we often have to dodge "critters", so all the light we can get would be helpful.

Does anyone remember this subject being posted?

Thanks, Flint.
 
That would explain why I could not find a post about it I guess.

I have never noticed! What a dumb-ass.

I will leave this post in place just in case some other nitwit should ask the same question.

I'm sooooooooooo embarrassed.
 
flint, don't worry about it. If you want more light, though, I'd highly recommend the Slee harness, and the HIR lightbulbs. I put both on at the same time, and now I have zero complaints about my lights, which were more than a little dim.

I think the stock setup is just a tad anemic. I don't know what it was like new, but when I got my hands on my '93, it sucked for lighting. Which is a really big deal, in the mountains.
 
flintknapper;1657375 I'm sooooooooooo embarrassed.[/QUOTE said:
You should be:D


I used a dremel wire brush to remove the coating from the end of the low beams....

It helped a bit, but some cheapo offroad lights with 100w bulbs pointed downrange and a little off to the side will work better. you can even disguise them as fog lights.
 
flint,

FWIW in the back country driving, which is very rare in Japan:D, I prefer just having the high beams by themselves than having both high- and low beams on. It makes me see better further out since the foreground is not lit up (bright).

As mentioned above, I would opt to add aux. driving lights, if that's an option.

Good luck!

Mot
 
Aussie versions don't have the low beams on with the high beams.
We have the twin square headlamps. The outer lamps are low OR high, and the inner lamps are high only.

Do your 80 series cruisers use H4 bulbs. If so then you probably don't want high and low filaments on at the same time due to heat build up for very little benefit of light output.

I've just finished installing an uprated headlamp loom and have already burned out a new bulb. This could have been due to the fact that unless you include a diode and resister to the circuit then the low and high filaments light at the same time, not good with a H4 bulb.
 
We do not have the H4 bulbs, we have 9005 and 9006 bulbs.
 
In Japan we don't have the quad square headlamps, but have the H4 outer (high/low) and the H3 inner fogs (with yellow cover), like some of you do in OZ (right?).

In Europe I think you could get those options plus the outer H4 and inner H1 (high) beam set-up.
 
blue-sml.jpg


H4 outer (low or high) these are 55/60w (or thereabouts) as standard, but I've fitted 90/100w
H1 inners (high) Ive fitted 100w
Lightforce driving lights (via separate switch in high beam circuit - legal requirement) 100w
 
Last edited:
Start with the HIR upgrades and slee harness for the high and low beams. If that isn't enough, get a set of Hella 4000 FF driving lamps (the brand new clear lens ones are supposed to put out a lot more light than the last generation) and wire them to come on with the high beams. If that isn't enough, stop driving at night.
 
Back
Top Bottom