Help with Man-A-Fre rear panhard Drop bracket

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 18, 2007
Threads
35
Messages
164
Location
MIAMI
Recently I lifted my HDJ-80, this is my current suspension setup:

OME J springs (front and rear)
OME L Shocks
Slee Caster plates
Slee 1” coil spacers(Front)
Man-A-Fre rear panhard Drop bracket (this was installed yesterday)

After installing the rear panhard Drop bracket I was expecting to see my rear diff centered, but it didn’t move, as a matter of fact it's in the exact same position.

Any suggestions or if I miss something during the installation please let me know. Here are the pictures:
DSC05670.jpg



DSC05667.jpg



Passenger side:

DSC05671.jpg



Driver side:

DSC05672.jpg
 
when the panhard is very close to horizontal, is when dropping it down makes the least amount of difference, as the arc of the rod doesnt change much.

An adjustable panhard rod is what you need to centre the diff, with those coils, normally around 9-12mm longer is required depending on actual ride height.
 
I had this same problem when I installed mine. There is a thread by me out lining this.

Basically you need to rotate the piece that drops the hole (not the brace) 180*. I had to do a little grinding on the side of it to get it to fit again. The drop bracket works fine but I had no instructions and had to work it out on my own.

Also before drilling the hole for the brace use a small level to make sure the new hole is plumb with the original, the truck needs to be on level ground when doing this.

Installed correctly it does a better job than a adjustable panhard at keeping the axle centered, but again MAF sucks with instructions.
 
It's practically impossible to get that thing lined up properly because you have to get that upper bolt hole you drill perfect.

At the point I had to buy an adjustable anyway, I sold mine and have never paid another bit of attention to it.
 
I have one too and it didn't chage a thing. you have to follow landtanks suggestion if you have the time. I called MAF about it and they told me that their bracket wasn't deisgn to center the axle, it was there just to keep it in a stock location. I spoke to them over phone and email. I didn't have a grinder handy so I just purchased the adjustable from Slee or you can buy the do-it-yourself also from slee. I installed the adjustable panhard with the braket still installed. Not sure what the bracket is actually doing now that I got the adjustable. If you want results, go adjustable.

-Juan
 
Thanks for the advice, I'll try Landtank's suggestion.

The bracket came with no instructions, I wrote them asking for a guide or something and got no respones at all, I think this is my last MAF product. I did search for some info on Ih8mud but only found something about the weak 8.8 grade bolt included in this kit.

BTW, this is the description from the MAF webpage:

80 Series Rear Panhard Rod Drop Brackets
When lifting an 80 series the panhard rods swing down, and move the axles sideways out of alignment with the frame and each other. These 4 inch drop brackets bring the panhard rods and axles back into alignment, and into the center of their designed travel arc @ 4" of
lift. Requires drilling of 1 hole in rear for installation. Sold each.
 
Yeah, I read that and still thought it was better solution but I bit the bullit and just purchased the adjustable. That was my last MAF product too!

good luck!

Juan
 
i just finished making a new panhard bar for my 80. a 1.5" id dom tube fits perfectly over the rear panhard. so just measure the current panhard and cut it someplace. slide the now 2 halves of panhard into a pice of 1.5" dom and weld it up making the panhard 3/4" longer than the orriginal. now you are done.

I thought it's not that hard to make your custom panhard .. ( actually believe that Juan make the Mario's one ) but should be a place with a bolt on already modified rear panhad ..

I know it depends on the lift and weight but maybe something standard as 2" more long .. ?
 
I got this repply from the MAF guys, seems like they're trying to solve this issue :clap::

Ricky
It looks like the unit was manufactured with the holes off center. I am having the shop test a kit on my vehicle and if it checks out, I'll send you a replacement. Sorry for the hassle
Regards,
 
I got this repply from the MAF guys, seems like they're trying to solve this issue :clap::

Ricky
It looks like the unit was manufactured with the holes off center. I am having the shop test a kit on my vehicle and if it checks out, I'll send you a replacement. Sorry for the hassle
Regards,

typical MAF BS. Look at my thread of some two years ago and it was pretty much the same thing. If you get something different post it up. But use the level to plumb the holes before drilling the hole for th e brace.

Another tip is to grind the seem in the factory mount flat where the hole needs to be drilled. That will help you center punch and drill that hole.

Rick
 
i just finished making a new panhard bar for my 80. a 1.5" id dom tube fits perfectly over the rear panhard. so just measure the current panhard and cut it someplace. slide the now 2 halves of panhard into a pice of 1.5" dom and weld it up making the panhard 3/4" longer than the orriginal. now you are done.

Dusty,

Did you perhaps mean 1.5" OD DOM?? I'm looking for a panhard solution - took my calipers and measured the diameter of the rear panhard on my ' 91....looks to be about 1.25" fat.

So .25" thick, 1.5" OD, 1.25" ID DOM will slide snuggley right over it???

Can anyone confirm??

Thanks!!
 
Back
Top Bottom