Help me guys... I suck at math.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 30, 2006
Threads
103
Messages
3,952
Location
Utah
So I'm trying to figure out my gas mileage, but I've got 35s (and stock gears) and have no idea how to correct my miles.

Here we go. Uncorrected, I went 166.3 miles on 20.106 gallons. I did a little work on the highway and found that (according to my GPS) when my speedo is reading 50 MPH, I'm actually going ~57.5 MPH, and the engine is turning 2650-2700 RPMs in 3rd gear.

So here's the big question: How many miles did I actually go? This is too many numbers for my poor brain... :confused:


Thanks
-Lane
 
191.2 miles... but are you sure you read your gps correctly? that is a 15% difference, I measured an 11% difference with 315s on my 92 with GPS and using mile markers.

Pretty sure I read it correctly. I held "50" MPH for as long as I could to make sure it was consistent.
 
Stock tires on my truck are 31x10.50x15. I'm running 35x12.50x15. A bit different than the 315/275/whatever stuff you guys use...

Joey, the tire size calculator would help a lot, but it doesn't have the sizes I'm using...
 
Your gps reading and speedo reading give you a ratio that describes the error in your speedometer. According to your readings, your actual speed is 1.15 times greater than what your speedo tells you.

or

your speedo is 15% slow.

Ok, got that... But how did you get 1.15 --> 15%?
 
You can use this to find your true percentage of change then adjust accordingly:
Tire size calculator


I used this to set my Marks speedo correction circuit initially. However, after repeated tests against a gps, the actual correction was slightly different. I think the final rolling diameter of a tire varies enough due to pressure and wear, that a good gps calibration is the best way to go.
 
So I'm trying to figure out my gas mileage, but I've got 35s (and stock gears) and have no idea how to correct my miles.

Here we go. Uncorrected, I went 166.3 miles on 20.106 gallons. I did a little work on the highway and found that (according to my GPS) when my speedo is reading 50 MPH, I'm actually going ~57.5 MPH, and the engine is turning 2650-2700 RPMs in 3rd gear.

So here's the big question: How many miles did I actually go? This is too many numbers for my poor brain... :confused:


Thanks
-Lane

Lane,

Assuming that your speedometer is off percentage wise the same amount as your odometer. Here are your calculations:

50MPH x 100 = 500 / 57.5MPH = 86.96%

This means your speedo is off roughly 13% (100-86.96=~13)

Uncorrected odometer reading of 166.3 miles * 1.13 (or 113%) = 187.92 corrected miles / 20.1 gallons = 9.35 MPG.

You could also calculate this based on tire size, but I would need your actual tire height (not published tire size). The easiest way is to track actual miles on GPS though, or get a Yellow Box.
 
>57.5 mph / 50 mph = 1.15

This is confusing...

You stated that your speedo read 50 MPH and that the GPS said 57.5 MPH. Imagine you drove an hour - your odometer says it traveled 50 miles - but your GPS says 57.5 miles. This ratio represents the difference between your new gearing and the stock gearing. That ratio does not change no matter what speed or time you travel - it is a correction ratio.

You said the odometer read 166.3 miles. Correcting it using the ratio above says you actually traveled 166.3 miles * 1.15 or 191.25 miles.

This ratio is also useful to know what speed you are traveling at. If your speedo reads 65 MPH you are actually traveling at 65 MPH * 1.15 or 74.75 MPH. (You will need to be going 57 or so on your speedo to actually be at the federal speed limit)
 
Ok, got that... But how did you get 1.15 --> 15%?

1.15 = 115%
We're just talking a simple ratio vs. a ratio per 100.

The 0.15 or 15% is just the difference between the two measurements.


It might be more intuitive to stick with the simple ratio, rather than the percent.
 
Ok, got that... But how did you get 1.15 --> 15%?

If you multiply a number by 1.15, you will receive an answer that is 115% of the original number. If you just want to know what 15% of the original number is, you would multiply it by 0.15.

A good example of this is when tipping for a meal out. People want to know how much to make their bill total for, including tip. First, they'll multiply their bill by 0.15, and find the answer. Then, they'll take that answer, and add it to the sub-total of their bill, to find the grand total. It's much easier, in my opinion, to just multiply the sub-total by 1.15 to arrive at the grand total.

($10 bill, times 0.15) + $10 = $11.50

OR

($10 bill, times 1.15) = $11.50
 
Lane,

Assuming that your speedometer is off percentage wise the same amount as your odometer. Here are your calculations:

50MPH x 100 = 500 / 57.5MPH = 86.96%

This means your speedo is off roughly 13% (100-86.96=~13)

Uncorrected odometer reading of 166.3 miles * 1.13 (or 113%) = 187.92 corrected miles / 20.1 gallons = 9.35 MPG.

You could also calculate this based on tire size, but I would need your actual tire height (not published tire size). The easiest way is to track actual miles on GPS though, or get a Yellow Box.


This approaches the problem from two different directions, and gets the wrong answer.

If you use this ratio:

Measured/Actual = .87

Then you need to apply this factor as the denominator (you need to divide the measured miles by 0.87)

It's easier to see on paper. It's hard to show the dimensions canceling typing on a keyboard.
 
1.15 = 115%
We're just talking a simple ratio vs. a ratio per 100.

The 0.15 or 15% is just the difference between the two measurements.


It might be more intuitive to stick with the simple ratio, rather than the percent.

Ah, making sense now.


If you multiply a number by 1.15, you will receive an answer that is 115% of the original number. If you just want to know what 15% of the original number is, you would multiply it by 0.15.

A good example of this is when tipping for a meal out. People want to know how much to make their bill total for, including tip. First, they'll multiply their bill by 0.15, and find the answer. Then, they'll take that answer, and add it to the sub-total of their bill, to find the grand total. It's much easier, in my opinion, to just multiply the sub-total by 1.15 to arrive at the grand total.

($10 bill, times 0.15) + $10 = $11.50

OR

($10 bill, times 1.15) = $11.50

I actually learned that trick from my buddy.... Never thought I could apply it to tire sizes and speed. Sweet.
 
Man, questions about tools and math always get quick responses.

....I think the final rolling diameter of a tire varies enough due to pressure....

As I will never forget, pressure doesn't affect the rolling distance of a tire (circumference). If it did, the tire would have to spin on the rim.

Without using the GPS speed and assuming the stock tire is 31.5" tall....

35/31.5 = 1.111

(1.111 can be considered a correction factor)

To correct your mileage, you multiply what your odometer gave by this number. 166.3 x 1.111 = 184.756. This what you actually drove with the larger tires.

Then, to get MPG, divide the actual miles driven by the gallons of fuel used. 184.756 / 20.106 = 9.189 mpg.

So, the GPS method is pretty close to the tire size method; 9.5 vs. 9.2 (assuming you had 31.5" stock tires before the 35s).
 
Back
Top Bottom