help identify ticking.

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Marvel has never worked in the engines I have tried it in, but Rislone works every time.
 
... My neighbor said it sounded like a sticking lifter and it should eventually go away after time. ...

Nope, a sticking lifter is a hydraulic lifter that is stuck collapsed, causing excessive valve lash. The Cruiser motors are solid lifter, in the case of the 1FZ bucket on valve design. If a valve or bucket were sticking the valve would be held open, causing a miss.

Valve adjustment or lifter tick can cause the noise, but most times they come on slowly, not suddenly.

My first test would be to find the source of the noise using a mechanic stethoscope.
 
Thanks for all your suggestions!

I would love to tear this thing down and rebuild it the right way..... but, i am a commercial real estate broker and i'm pretty much busted right now. Things are looking better but i have ZERO extra cash on hand right now. When i get back on my feet i will rebuild the motor the way it needs to be to last another 200,000+ miles.

Ever since this happened and i tried to start the motor with the timing 180 off, i wonder if i bent a valve? I guess i would really know that if it were in fact the case.

It's a pretty pronounced ting, ting, ting, ting......
 
I never have been able to get rid of all my ticks.....

Seriously, though, these engines sound like a sewing machine on steroids, if it ticks and the valve ajustment is all good, why worry? I've listened to a lot of 1FZFE's and they all sound the same to me, lots of valve train noise. I can listen to it it for hours on end.
 
I know the top end of these motors make some racket. This is totally different. It's a definitive tick, tick, tick... with a bit of metal sound. Maybe more like a ting, ting, ting....

If we get a period of clear weather (since i don't have a garage) i will check the valves.
 
Just a guess, but since you had your distributor out a couple times, is it possible that something inside the distributor is coming into contact with the rotor and making the noise? The plastic cap could be amplifying the sound.
 
That's a ten minute fix if it's the case. Sounds like a good place to start to me.
 
best i can tell, it seems like it's coming from the middle to front half of the motor and it seems like it's coming from in the head or where the head mates to the block. That's my best ruff guess by standing around it while it's running and sticking my head/ear all around the motor.
 
best i can tell, it seems like it's coming from the middle to front half of the motor and it seems like it's coming from in the head or where the head mates to the block. That's my best ruff guess by standing around it while it's running and sticking my head/ear all around the motor.

I'm not sure you want to be driving that thing, not knowing what's causing the noise.

remember this thread?


https://forum.ih8mud.com/80-series-tech/242439-1fz-engine-teardown-w-pics.html



That was a really severe case of piston slap that ended up with a broken piston skirt. That kind of noise starts as a sort of "tick" noise, (usually diagnosed as either wristpin knock, or piston slap, they sound almost identical) rather than the dull knock of a rod knock. Also the noise will be much higher in the block than a rod knock.

Piston slap will 'usually" (but not always) be worse when the engine is cold.
 
I had a piston ring go at 245,000. Blew the pieces into the exhaust, still ran fine.The piece of ring that stayed on the piston made a noise like...ting, ting, ting. I hope that's not your noise
 
I think the thing to remember in this case is that the truck sat for 4 months. I think it's a stuck lifter.
 
I think the thing to remember in this case is that the truck sat for 4 months. I think it's a stuck lifter.

How is that possible? The 1FZ doesn't have hydraulic lifters. Doesn't really even have traditional lifters, it's a bucket type lifter on valve design. If the whole lifter were stuck, the valve would be held open and have no compression in that cylinder, so would miss.
 
I'd buy a $15 mechanic's stethascope in a heartbeat if I had a new engine sound like that. Forget the 'stuck valve/lifter' stuff - it's something else. Could be an injector got gummed up sitting around, could be a bunch of things. But being there at the engine block listening to specific areas and pinning it down to a 6" radius in mere minutes would be the way to go.

DougM
 
I did, and i can't believe that i didn't finish this thread! I thought i had...

So, turns out the ticking was from the power steering pump. When i replaced the pump, you have to put your old gear, from your old pump, onto the new pump. There is nothing other than a torque speck to tell you how to seat the gear. Turns out that if the gear is not fully seated then you will get gear chatter and that was the ticking i was getting.
 
We may have a completely opposite sound mind sounds like a very faint knocking but it is not a rod or bearing pretty sure of that. The noise has stopped a few time but only for few seconds. I changed my power steering pump out but did not check torque spec when i put the gear back on... Think i should redo it?
 
I'm not sure it really has anything to do with the torque spec, but more with how well the gear seats on the shaft. If that makes any sense. You could torque it to spec, but if it's not fully seated, it will tick.

And, in my opinion, if you don't have a baseline measurement to go by, then it's hard to say if it's seated fully or not.
 
Back
Top Bottom