*!^#*&^($!*&#^ Head gasket!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 25, 2005
Threads
29
Messages
289
Blew the head gasket in the 94 the other day so now I know how I'll be spending my weekend. :bang:

Wondering if you guys think I'll need to get the head re-surfaced or not. Also, the truck has 160K on it and I'm wondering if there are any mechanical "while I'm in there" things I should do?
The truck has basically only had the regular maintenance stuff done, so what's going to fail next that I should go ahead and replace now? thanks...
 
Blew the head gasket in the 94 the other day so now I know how I'll be spending my weekend. :bang:

Wondering if you guys think I'll need to get the head re-surfaced or not. Also, the truck has 160K on it and I'm wondering if there are any mechanical "while I'm in there" things I should do?
The truck has basically only had the regular maintenance stuff done, so what's going to fail next that I should go ahead and replace now? thanks...

YES YES YES get it resurfaced and checked for cracks! As far as what to work on while yer in there, do a valve job, get the injectors cleaned and balanced, replace all the cooling and heating system hoses, perhaps a new fan clutch and perhaps a new radiator depending on the condition of those two things. I, as always, got all my parts from Dan the Man and he advised me on what was needed or not needed to suit my specific interests. HTH. :cheers:
 
The other things i would do. Go ahead and pull the intake plenums and have them cleaned. If you haven't done the starter contacts, do it now. PHH and fuel filter are up there as well.

Buck
 
No, no, no... Just get the valve seals from Dan and have a shop clean and check the head while they're installing the new seals (guides) and doing a valve job. Odds are WAY against you needing the head machined - just the normal cleaning and pressure testing they do for the valve job will be fine. Sure, if it's not flat you'll need the machining done but don't plan on spending the money. Better to have the injectors cleaned. Also, good advice on cDan the parts man and checking the condition of your radiator (any idea if it got hot??)

DougM
 
While you're in there....
-crankshaft seal and oil pump seal R/R
-fuel filter (as mentioned)
-water pump
-T-stat
-Fuel Injector clean/balance
-radiator pull out rod and flush
-change out radiator hoses
-change out PS low press hose (Previa hose per Mud board).
-R/R fan clutch (not necessary but everything will be off!)
- still thinking....
 
No, no, no... Just get the valve seals from Dan and have a shop clean and check the head while they're installing the new seals (guides) and doing a valve job. Odds are WAY against you needing the head machined - just the normal cleaning and pressure testing they do for the valve job will be fine. Sure, if it's not flat you'll need the machining done but don't plan on spending the money. Better to have the injectors cleaned. Also, good advice on cDan the parts man and checking the condition of your radiator (any idea if it got hot??)

DougM

Doug this makes no sense whatsoever. You're saying don't plan to spend the money unless it needs it. Talk about failing to plan and planning to fail! And this is coming from the guy that replaced the same rig's HG two times within what 10K or 20K miles right?!? You didn't even initially have your head checked which was why you found out it was cracked after you installed it and blew the replacement gasket and then you still wondered what you could cut corners on with whacked out repair shops. Hmmm? Made no sense then and makes no sense now. :doh:

To the OP, to clarify the answer I provided IF your head is perfectly flat ((unlikely depending on how hard and how long (time it took while it was failing) you blew that gasket)) and IF the surface of the head is perfectly smooth (50/50) then it indeed makes sense to save the money that you otherwise PLANNED to spend. However if your head is warped in the slightest or scuffed in the slightest please don't take the risk of replacing the thing right away. There is also more and more research that with iron blocks and aluminum heads the smoother the surface of the head the better to prevent the shearing forces that help to harm the HG's. Don't get me wrong, if it all checks out straight and smooth consider yourself lucky and save some $$$, but please do plan to totally take care of this thing the first time; you don't want to repeat the trouble that Douglas went through!!! :cheers:
 
I would definitly have the head checked to see if it was warped during your overheating/headgasket blown incident.. Mine was, and I was about to slap it on without having it checked out. The machine shop owner later told me if I had thrown it back on the block and ran the head the way it was, I would have definitly blown another gasket...
 
FYI, it isn't that expensive either, it was around 150.00 for the re-surface, check leaks etc..
 
Make sure to take the Knock sensors out of the block right after removing the head. There are quite a few people that find that the plastic top gets broken while working on the Head. Ask me how I know this!!! A new knock sensor from Dan-o is about $120.00.

Also don't forget to put a new PHH on when the head is offi. You can get to it really easy now. I also changed all the vacuunm hoses undernieth the Intake Manifold since it was off and I could get to it. Here is what I replaced: (maybe a little overkill but I wanted to be sure)
1) Water Pump
2) Thermostat
3) P/S pump, High pressure hose
4) Fuel Filter
5) Fan Clutch
6) Alternator brushes
7) PCV
8) Coolant hoses
9) Rebuilt head plus shaved .008" t0 get rid of corrosion at back of head
10) Fan Belts
11) Vacumn hoses

And probably some other things I can't remember now.
Have fun! Take you time! Don't forget to plug the #4 Fuel injector in... (don't ask)
 
Last edited:
How about a 3FE transplant!!:doh:

No, just joking, good luck on the work ahead of you.

:cheers:
 
Thanks for all the input guys. The radiator is fine. I serviced that last fall. Now I just need to find a decent maching shop in/near Philly.

BTW, what is a PHH?

Not knowing how rusty your hardware is, might want to soak everything down with PB Blaster and plan on breaking and purchasing new hardware!

PHH - Pesky Heater Hose. Check the FAQ section for a detailed writeup on this. Once the head is removed, you'll have loads of space to work by standing on top of the block.

I concur with swapping out the ALT brushes since you'll have to remove it out of the engine bay anyway.

Where abouts are you located?
 
Turbo,

My 97s head did not blow a second gasket - it turned out to have a crack after reinstallation and I bought a new gasket to button it back up with. As for planning to fail, etc perhaps I should clarify that I don't think you need to walk in with the head and request it be resurfaced as you may not need it - needless expense. Any competent shop will do a thorough cleaning and flatness check on any head they've done a valve job on as well as a pressure test. It's fine to also insist on having additional machine work done to either mill it or completely resurface it as I did but not needed.

So, I guess I'm assuming no matter what else he does, he's going to bring the head to a shop and have new valve seals fitted and a valve job - which means the head will be checked. If he's thinking of just slapping the head back on on a 15 year old vehicle with 160,000 miles on it then I don't agree with that as my own experience showed. Cdan has a great price on the valve seals and it's cheap to get a valve job at the same time. Then the engine's ready for another 200,000 miles.

PS - didn't mean to be so confrontational with my "no no no" thing. Wassamatter - too much coffee in the afternoon??? Heh...

DougM
 
It is important to remind that the factory says that the head is not to be surfaced at all and should be replaced if the mounting surface is not within specification.

I bring this up because it should not be infered that this is a normal practice and is "OK" to do. It is not "OK" and anyone who does so is doing it at his own risk.


On the other hand it's been done lots of times with success, it just aint "legal".

:lol:
 
Turbo,

My 97s head did not blow a second gasket - it turned out to have a crack after reinstallation and I bought a new gasket to button it back up with. As for planning to fail, etc perhaps I should clarify that I don't think you need to walk in with the head and request it be resurfaced as you may not need it - needless expense. Any competent shop will do a thorough cleaning and flatness check on any head they've done a valve job on as well as a pressure test. It's fine to also insist on having additional machine work done to either mill it or completely resurface it as I did but not needed.

So, I guess I'm assuming no matter what else he does, he's going to bring the head to a shop and have new valve seals fitted and a valve job - which means the head will be checked. If he's thinking of just slapping the head back on on a 15 year old vehicle with 160,000 miles on it then I don't agree with that as my own experience showed. Cdan has a great price on the valve seals and it's cheap to get a valve job at the same time. Then the engine's ready for another 200,000 miles.

PS - didn't mean to be so confrontational with my "no no no" thing. Wassamatter - too much coffee in the afternoon??? Heh...

DougM

That all makes perfect sense Doug and my sincere apologies about something in specific; I thought you discovered the crack by blowing the HG so rapidly after replacement and I thought you deliberately didn't do anything at all machine shop wise the first go-around. I didn't re-read those two threads before posting in this one, I just remembered sympathizing with you at the time (internal thoughts of "poor sonofabitch") when you went through that trouble those two times and then basically being astounded that you would suggest someone take a similar chance at avoiding something that might be wrong now. I didn't realize you had your head checked and they missed the crack or that the crack came after installing it again. Again, my apologies. I think that we would all agree to have the thing checked by competent machine shop and fix only what is wrong along with all the appropriate valve work regardless. :cheers:
 
IdahoDoug's head gasket DVD was a big help for me since it was my first time. There are several shortcuts that save time over the factory process.

when I did mine I

- had head checked for flatness
- valve job done
- cleaned and balanced injectors
- replaced PHH (pesky heater hose. You HAVE to do this while you're in there or you'll kick yourself later. Very hard to get to without the manifolds out
- put new starter contacts in
- put new alternator brushes in
- new fuel filter
- new water pump
- still need new fan clutch
- cleaned intake manifold as much as possible


there's lots of stuff you can do in there.


Mine runs a lot better but it's had a very strong gas odor since I did it. I can NOT find out where it's coming from. it's killing me. I wish I could track it down.
 
Back
Top Bottom