HDJ80 93 autotrans problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2019
Threads
1
Messages
4
Location
Norway
I have read a few forums, here home and on the world wide web, found most threads here, but noone seems to fit my problem, so created a profile, and here goes;

My GF got a hdj80 because i said that was best car :P
it has done almost 480k km now 1hdt

2 problems;
when in reverse, it slips out when passing 15-20kmh, then it slips out of gear and in again constantly, if i slow down it works nice. it has done it a few times from standstill when you touch throttle but thats FEW times.

second problem:
when driving in 4th on highway, suddenly it feels like the lockup stops or something, this happens when warm mostly, but sometimes the car can work nice for a few weeks, then it can be hopeless a few trips and the problem is on and off, solving is mostly: put it in N and back into D, or use OD on and off, or pwr buttn on and off.

the gearbox has been flushed with cleaning additives, the old oil was dark brown, but didnt smell too bad.

sorry for bad english, hope some of you might have a clue for me.
i got a used valvebody extra im thinking of just trying to change it too see, but my head tells me it might be some electrical funky buisness

its got L 2 D N R P and im pretty sure its a 442
 
Yes, you have the A442f transmission. On the freeway, are you sure you are not feeling the torque converter lockup and unlock because you are cruising that exact speed (50 mph) that it is set to? If you shift to 3rd, do you still get that behavior? Is the trans/torque converter full of fluid? I don't know much about auto transmissions (the LC is my first) so sorry I can't be more help.
 
fluid is good, it can happen at diffrent speed. but usually only in OD gear, im pretty sure its the lockup that slips, but it shouldnt be a reason for it to do that, speeds from 80-110 kmh it can happen anytime, and it doesent happen all the time
 
You have the electronically controlled version of the A442F seeing as you have the O/D on/off and power on/off buttons.

For the 1st problem, what happens when it slips out of reverse? What sounds does it make, what do the RPM's do, can you explain in detail what's happening here?

For the 2nd issue, the torque convertor will lock up in 3rd and/or 4th/OD on these transmissions, mine seems to do it around 80-85km/h. I'd do some testing by driving with the OD button off which prevents it from shifting up into 4th/OD, and make sure it's locking up and staying locked up for you in those conditions. Then do the same with the OD button on so it shifts into O/D and then the TC should lock at the same speed as before. See if you can identify when the issue is happening, and make sure it's actually the torque convertor that's the issue, and not an issue with shifting to and staying in OD.

There's a shift linkage that attaches to the injection pump throttle linkage that can be adjusted, and if out of whack can cause all sorts of driveability issues. I'd do some testing to narrow down your issue before I started changing things though.
 
havent tryed to drive with od off, ill try that. forgot to say that the previous owner has had the converter changed, so in theory that should be good.

with the reverse it just feels like the gear slips out as if you put it in N and back into R, revs go up when it slips out, then down again when gear engages back in.

ill have a go at the shift linkage to the pump. just wierd that it sometimes is just fine. tho the reverse problem is all the time if i try to back it up fast ; 15kmh +
 
When it pops out of reverse, is there any gear grinding noises/feeling?
 
no bad sounds, just nice like normal "gear change"
 
no bad sounds, just nice like normal "gear change"

Maybe it's as easy as adjusting the actual shift linkage under the console to resolve the reverse issue?
 
My LC acts weird sometimes in gear shifting too.


I bought it 4 months back with 200K km clock and changed all the fluids, greasing, electrical issues, etc.


After start & little warm up, I put it in D and push the accelerator. Its automatic but I can feel very well when it changes the gear by itself. Sometimes it stuck & does not shift from 2nd to 3rd gear. Then If I keep giving it accelerator, the RPMs goes up, engine sounds increases, but it does not shift into the 3rd gear. It really looks bad when you are on the road and people are in queue behind you because your jeep is not shifting gear.


But after sometime, it automatically start working good.


Have checked up with some mechanics, they said the Gear & TC need to be open as some pressure plates are slipping. Cost will be ~1K.

I asked them to check the gear wire from lever to gear as it stuck somewhere or doing fine? They checked and say its fine.


I’ve run it 10K in last 4 months and planning to change the gear oil again (ATF D-III or T-IV) alongwith engine oil change.

Thinking to add some “gear slip stop” liquid. But I am not sure if it will work.
 
The FSM have the procedure to check the 4 solenoids on the tranny .. other than that FSM also have the procedure for stall test ( TC ).

Beyond that checking the pressure on lines on the tranny will be more involving I guess, never went down that road ..
 
My LC acts weird sometimes in gear shifting too.


I bought it 4 months back with 200K km clock and changed all the fluids, greasing, electrical issues, etc.


After start & little warm up, I put it in D and push the accelerator. Its automatic but I can feel very well when it changes the gear by itself. Sometimes it stuck & does not shift from 2nd to 3rd gear. Then If I keep giving it accelerator, the RPMs goes up, engine sounds increases, but it does not shift into the 3rd gear. It really looks bad when you are on the road and people are in queue behind you because your jeep is not shifting gear.


But after sometime, it automatically start working good.


Have checked up with some mechanics, they said the Gear & TC need to be open as some pressure plates are slipping. Cost will be ~1K.

I asked them to check the gear wire from lever to gear as it stuck somewhere or doing fine? They checked and say its fine.


I’ve run it 10K in last 4 months and planning to change the gear oil again (ATF D-III or T-IV) alongwith engine oil change.

Thinking to add some “gear slip stop” liquid. But I am not sure if it will work.


Can also check the drive plates on the front hubs. If one of these is stripped, it can cause slipping.
 
Can also check the drive plates on the front hubs. If one of these is stripped, it can cause slipping.

If you had a stripped driveplate, would you not have a complete failure rather than an intermittent slipping? As in, any time the CDL was unlocked, you'd be sending all the power to the front wheel with the stripped driveplate and the truck wouldn't move? I guess the viscous coupler could complicate matters (I don't have one), but I'd still think you'd be hard pressed to actually drive the vehicle if that was your issue.
 
If you had a stripped driveplate, would you not have a complete failure rather than an intermittent slipping? As in, any time the CDL was unlocked, you'd be sending all the power to the front wheel with the stripped driveplate and the truck wouldn't move? I guess the viscous coupler could complicate matters (I don't have one), but I'd still think you'd be hard pressed to actually drive the vehicle if that was your issue.

Depending on the amount of debris in with the drive plate and if there is the presence of a VC, it MAY cause an intermittent feel like that.

I'm just fishing for ideas that may be less expensive and outside the box.

There have been a few here that swore their T-Case was dead when it was drive flanges.
 
Back
Top Bottom