Harmonic Ballencer -!!!!WITZ END!!!!-

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 20, 2015
Threads
12
Messages
56
Location
Los Angeles
To give some background: So I am in need of some real guru advise here. So I work for a dealership and work on my truck there with my buddies who help here and there and lend tools if I dont have them, but non of them are Toyota techs so there point of few is all VW stuff.

My Issue: I own a 1997 Landcruiser which has been a champ and has never given me an issue but this is the 3rd harmonic ballencer I have to throw on her. When I bought the truck it had a front main seal leak and I thought easy I can do that in 2hrs no big deal. So when I pulled off the first ballencer the keyway was chipped on the top but pulled out easy and the ballencer was cracked on the shaft near the end of its shaft were it follows the keyway. I put all new stuff on and had no leak for a week then after a trip to vegas and back I saw a huge puddle assemble under the truck, so I look and see the front main seal leaking. So i pull it apart and see the same issue; the ballencer cracked/chipped yet the key way was fine that time. So i part warranty the ballencer at toyota and throw a new one on. Good for a month and now leaking again, pulled it apart at work and the thing is cracked again!!!! FML!!!

Please I may commit suicide here. Any help or fix will make me owe you in great dept. I'm located in Los Angeles and willing to help anyone on working on their rig.

Thanks,
Luke
 
Talked to 3 toyota shop foremans and they all say put blue lock tight then hit it with the impact. I have also done it with a wrench on the second time thinking impacting it is messing it up. Not the case
 
I worked for a Toyota dealer then VW. Even among Toyota techs, not many are familiar with the old Cruisers. The ones I worked with that were emphasized using their snap-on impact (tools weren't shared at that shop) to ram the crank bolt on, then hammer on it till it won't go on anymore. Think of taking a CV axle bolt loose and replicate while tightening the crank bolt if you don't have access to a big enough torque wrench. It really is surprising just how tight 300 ft-lbs is. I may get flamed for advising how to not use a torque wrench, but working in a shop they are hardly used. I can't remember the last time I stripped something out or something came loose.
 
You have hell to pay if things aren't torqued properly. There are two things that are universal about 80 series MUD: 1) go OEM and 2) always torque to Toyota specs.
 
I have followed torque spec when applying the second time. Its not coming loose because i will watch for play and never seen her wobble. I think there is something bigger at play.
 
Have you checked the end of the crank for flaring? When you install the balancer are you inspecting the inside to ensure there are no runs or sags of whatever coating that is on them has run down inside? Are you coating the seal lip with a dab of grease and the inside of the balancer shaft with fresh motor oil? A good way to know whether things are not right is to remove the woodref key and spin the balancer on by hand working it back and forth and the removing it the same way. Tedious and time consuming but it gives you a good idea of whether it's hanging up or not. Also, NEVER impact the balancer on unless you're sure that it is completely seated prior to tightening. Have you inspected your lower timing gear to make sure there are no issues there? When you install the balancer are you using the old woodref key? Try using s new key. Ensure it isn't tilted when installing the balancer. I've never had a problem like you're describing, but I'm sure that there is something more to the issue. It's either a machining issue or it's an installer issue. I know plenty of techs who are decent techs and terrible mechanics....Oh Yes, there is a significant difference between a service tech and a real mechanic.
 
Im going to pull that key out and play with the ballencer feeling for issues. When toyota delivers my parts here ill start looking at things. Thank you
 
So I think we figured it out guys. I had a "pro" look at it, and he showed me a thing or to. He noticed an issue at the end of the crankshaft were the key sits after pulling the key out; and saying it was up side down! I was like huh? Then we took a pick and pulled a broken key out of the slot. I was surprised and dumbfounded. Having a flat surface i thought the key sat with the round side facing up but not the case when the slot is cleared. Our guess it after tightening the bolt it shatters the ballencer. Crazy.

20151211_180456.webp
 
Sense i had all the stuff out of the engine bay i went to town and started installing a new valve cover gasket, throttle body cleaning(she now starts after two clicks on the starter) and oil pump gasket. Big thanks goes out to my colleague Leo.
20151211_201601.webp
20151211_205233.webp
IMG_27411.webp
 
Btw, could you change the title and add *solved* to it? Helps with future searching.
 
(she now starts after two clicks on the starter)

Why two? It should start the first time you hit it, right?

Glad you found that the woodruff key was upside-down. That's weird though. Any idea how it got that way?
 
had a feeling. If you look at the key way You'd notice that it is cut into the crank in semi-circular shape to fit the rounded portion of the woodref. Applies for all mechanical things keyed. Glad it was a quick find.
 
Back
Top Bottom