FZJ80 Axle Housing replacement?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 16, 2015
Threads
9
Messages
30
1997 fully locked. stock.

Just ordered a set of 30mm spacers hoping to fit some firestone destination 315/75/16 on the truck until i can pickup ome 2.5.

Anyway, in preperation i went to pb blast the rear lower shock mount bolts and what i saw was distubing. The bracket looks like its rusted so bad. The whole axle housing looks rusted to hell. What kind of axle housing doni need and where can i get one?

Thanks!
 
Cruiseryard.com
Jason is awesome... @arcteryx you have a replacement, right?
 
I am located in Eastern NC however the trucks previous owners were in VA for about 15 years.
Here are some pics. Now that its brighter outside it doesn't look as bad as I thought except for the back side of the rear shock mount.

IMG_1008.webp


IMG_1009.webp


IMG_1010.webp


IMG_1011.webp


IMG_1012.webp
 
I'd just fix the axle seal and call it good.
 
If you are really wanting to do something, remove the axle housing, sand blast it and have it painted OR get some POR15 or other paint over rust product and follow the directions. I would bet that a used housing, bought and shipped unseen would be in the same condition.
 
I highly doubt there is a issue. The shock mounts are beefy as hell. I would be more worried about getting the lower shock bolt out.

Also, if your worried about the rust leave the axle seal alone.
 
Hit that orange stuff hard with a chisel or a screwdriver. You'll see that there is good shiny metal under that orange "patina".

Scrape it & paint it.
 
I should have asked for pics first. I assumed when you said "rust" you meant "RUST." You have no issue there. You'll be fine.

For reference, I'm in Michigan where we salt the roads up until nearly may sometimes. Rust eats cars for breakfast here.
 
In California that would be a lot of rust. Anywhere else, it's fine. It looks like that truck was used to launch a boat in salt water. If that were mine, I might clean it up a bit, but that axle is still solid and fit for use, likely for as long as you own it.
 
It looks like that truck was used to launch a boat in salt water.

Not really. I've replaced two axles now, one from Cape Cod and the other from Rhode Island. Both cases there were missing pieces that fell off the axle.

One lost a sway bar mount and both backing plates were considerably smaller. The other lost the LSPV bracket on the diff, e-brake support and the frame bracket for the LSPV was in three pieces.

Then add the typical seized bell cranks, brake line tabs and rotted brake lines.

I had one truck that I refused to work on. It was a 1992 and there just wasn't enough left to the old girl to rebuild it to where it would be road worthy.
 
California is a PIA for many Land Cruiser related (smog) problems, but rust is not one of them. I just got a 96 junkyard 80 axle for the rear of my FJ60 and not a spec of rust. The factory paint even still has a bit of gloss. The fasteners all came apart without issues. Rusting brake lines, never happens. Occasionally rear frame rust on early FJ60s is a problem, but only if they were originally sold back east.
 
Mines just as bad if not worse. Lspv is seized on. Most of the bracket bolts and stuff back there are rusted beyond wrenching it undone. I cut the e brake loose and rebuilt it. My next 80 is coming from a rust free zone for sure. I break a bolt every time I work on it. Buy a good drill lots of bits a tap and die set and a good cutoff wheel
 
That axle looks good to me. If you need one, I have a rear axle with locking diff in my garage. Just pm me if you are interested.
 
Back
Top Bottom