Full time to part time

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Entertaining?

First, I typed "really fun", but I usually like to be conservative. :D

As I've said, I can't compare it to/with awd.
Aside from it being bigger and higher center of gravity it feels just like driving a regular rwd (sports) car that I've driven in the past. :hillbilly:

I didn't mean it "entertaining" as in it's twitchy, etc...
Coupled with 5spd and (diesel) turbo it's REALLY fun to drive.

Besides, it doesn't snow where I am and besides, I'm the only one driving it. So I would not be reaping the benefit of awd anyway (Knock on wood!) I'll have my wife post here to let you guys know that I died in a car accident after losing control in my part-time 80 or something. :flipoff2:
 
I did the poor mans conversion with my 3FE. Noticed no difference in power or MPG.
 
I'm suprissed you didn't notice any difference fiveo, mine is like night and day. Plus you have 33, what about gears? I have stock tires, and in AWD the 3FE is really taxed trying to accelerate. I know the cruiser is not a Ferrari, but in two whell drive it was like i was in a porsch, kinda, almost, well, compared to before.

My engine is a dog though, its had a long life. Trying to get up to speed on an on ramp I have to punch it.

"Daddy, can we stop and get a slush puppy?"
 
Another way--way cheaper--to go 2wd is to get the center differential lock button/switch, pull the front drive shaft, engage center diff lock, and be 2wd using only the rear driveshaft. Poor man's 2wd.

It'll net you maybe 1mpg more, and some lessened wear on your front end--specifically the birfields. I've been doing this for awhile and just plan an extra ten minutes before a trail run to get underneath the truck and put the front driveshaft back in.

-o-


Is this the switch next to the antenna switch???:hhmm:
Just my 2 cents; I have driven my 60 (defunct) and now this 80 and the difference in fuel savings is about the same... lousy. I don't think I would convert my 80 to part time just for the fuel savings, I would look in wear of parts. Like it was mentioned here, these systems have been around for a while and they hold up pretty good.
:cheers:
 
FWIW I have driven both in frontwheel drive and rear wheel drive over the years. In both cases the handling is much less predictable in slippery conditions. There was zero difference in acceleration and MPG as we're still pushing (or pulling) the same weight around and the same parts are rotating. Not sure where Tenzig got the "sportscar" analogy from, but that just is not the case. He did mention birfield damage. Perhaps his front driveline was removed?

In any case I could never justify a PT conversion on my rig. I like the way it handles and the ability to simply push a button and lock things up is priceless to me. But, that's what makes a horse race.
 
With the poorman 2wd the birfs will still spin but they won't be under load so perhaps that might help birf wear a little bit.

IIRC, one point someone brought up is that with even with lockout hubs, the birfs/axle shafts are allowed to spin inside the spindle (increased spindle wear) because these are full time tranfer cases even though no power is tranfered to the wheels.


With the part time kit and the free wheeling hubs disengaged the axels don't spin. There is no drive from the transfer case and the free wheeling hubs disengage the hub from the outer axle so they don't turn.

Never really noticed a difference in MPG but there is a deffinite increase in power running in 2wd. Also 2wd low range is good for backing up steep inclines
 
This is the response I got to my email to Slee Offroad.

Regarding your Part Time Kit with freewheel hubs for the 80 series Land Cruiser

Part#: SOF1224 - $660.00
Fits '91-'97 Toyota Land Cruisers
Required Center Diff Lock Switch

As I already have the CDL switch installed am I to understand that this kit will allow me to use 2WD or 4WD in high range with a selection of the switch?

[CS]
Yes,


Will I lose my ABS braking system?

[CS]
Only when you are in 2WD mode and the front hubs are unlocked.


Delivery time?

[CS]
In stock
.


[CS]
Christo Slee
 
If I need front wheel drive .. as easy as I loch my hubs and engage my H4 button on the dash .. but I found my self driving under poring rain without problems in rear wheel drive only ..
 
Don't get me wrong anyone, I love the cruisers AWD, and since I have done the front end rebuild and put two new birfs in and new front UJoints, its as smooth as butter. With the OME lift I feel like I'm driving a cadi.

The 3FE has 17 years and 295 k on it, drives fine but in my opinion feels kinda weak, given what it is. I'm going over all the emissions and ignition now that its warmer, to see if something else isn't quite jiving, but again, the difference in two whell drive and AWD was like night and day, way way way more power in two whell drive. I notice the difference the most between the speeds of 35-55 MPH, like when trying to get up to speed on an on ramp to an interstate.

I did the test between AWD and PT twice, for months and thousands of miles, and both times I could feel the difference immediately. It takes more energy/power to rotate the front end parts, friction and rotational inertia, regardless of how much you weigh. AWD saps my engine, PT does not. If I had a larger or newer stronger engine, the difference might not be noticable.

When in AWD, or 4wd, the front end stays lower during acceleration, and turning. You can feel the front end pulling you, keeping you lower. In two whell drive its all back digging in, your front end rises during acceleration, and is much lighter in the front while turning, or more importantly while accelerating out of a turn. This isn't scary or drastic, like you'll jump in punch it and hit a wall, it just feels differently and acts slightly different. I thoroughly enjoy the feeling of the LC in PT, turning a corner, punching it on pavement, hauling tools or trees, driving down a dirt road, just about anywhere and anytime i drive. Rarely do i ever need 4wd. From what i understand most LC in the world come stock PT, I guess Toyota was feeling the same thing I was.

Its all about what you need and want. Do i want AWD, of course, when i hit the button and lock the hubs, otherwise 99.9% of the time I don't need it and i like the feel of it in two whell drive.
 
Enlighten me, please! What's the advantage of AWD without a VC? I might be wrong, but IMHO if your 80 is of the vintage without the VC, it makes sense to either have the poorman's PT, factory PT or get the kit. Without the VC, if any wheel has no traction, you don't move. You might as well have 2WD - less moving parts, and less drag on the already straining 3FE or 1FZ. The VC is what makes full time worth the extra expense of living with AWD. If you don't have it, part time makes a whole lot of sense. The owners of Detroit monsters of old fought that battle back in the 70s and 80s (without the VC of course) and finally came to realize that full time 4WD without a locker (while T/C was unlocked) was a waste. Limited slip helped a little, but was next to useless offroad.
 
Last edited:
Anyone mention how lousy the cruiser drives/ handles in 2WD? I did the rich "poor man's" conversion using lockout hubs and no front shaft. I hated the way it drove after that. I'm now back to AWD full time- I left the hubs installed, however.
 
Just and FYI for all those saying that dropping the drive shaft is the same as having part time....it's not. Once you actually have the front end freewheeling; locking hubs or removing the drive flanges, it feels much different than with the driveshaft gone and all the internals still spinning. Different = better.
 
As for everybody talking about the way it drives, I'm going to give you my opinion: I'm running approx 5" of lift, bias ply 37" Iroks with no balancing weights, no swaybars and no castor correction. I highly doubt that a part time kit will make my 80 handle any worse! LOL
 
80t0ylc, exactly!

If you don't have a VC and your truck is AWD, you're actually worse off than an open rear end RWD setup.. you have twice the odds of losing traction at a wheel and being stuck. Without a VC, you must lock up the center diff to gain any traction benefit.
 
What I'm slowly learning is the differences in AWD systems. I actually thought they were all alike. What confuses me is why Toyota built or builds Land Cruisers in both PT and AWD models. I realize they are trying to appeal to a variety of buyers but in reality it appears that PT has merits, at least in some countries. Was AWD just a marketing decision as to what would sell best in the USA or what should be built from a cost stand point? I believe it has merit since virtually all Land Cruisers are "pre-built" rather then built to order like one would if buying a new F250 Ford should the customer choose to order one. I have found this thread to be very informative and appreciate the different viewpoints everyone has. I can now see how this can get addictive.
 
As for everybody talking about the way it drives, I'm going to give you my opinion: I'm running approx 5" of lift, bias ply 37" Iroks with no balancing weights, no swaybars and no castor correction. I highly doubt that a part time kit will make my 80 handle any worse! LOL


Chad, I'd agree, especially for those who modify as much as yours, PT kit with hubs would help to keep wear to a minimum for DD or from home to trail. You prolly wouldn't notice much mpg gains, though.
 
It's true that AWD is pretty much useless in an off-road situation. On road it works very well, the drive is split between all 4 wheels, so it's much less likely for a tire to break loose. Driving with AWD it's almost impossible to spin a tire, pull the rear shaft, in FWD it's easy to do burnouts.
 
80t0ylc, exactly!

If you don't have a VC and your truck is AWD, you're actually worse off than an open rear end RWD setup.. you have twice the odds of losing traction at a wheel and being stuck. Without a VC, you must lock up the center diff to gain any traction benefit.


You know, I think that was the appeal - push the button (CDL in our case) or just shift into 4H lock for the Detroit rigs. You don't have to get out and engage the hubs. I guess it worked for a while.
 
I can't comment on a rig with a VC in the center diff, but I can say that even without one the LC80's AWD system works great to keep the rig pointed where you want it to go and going there; on road.

When I was rear locked, front open, center open I could pull some mean one front tire burn outs. But it was always the inside tire to break loose...meaning that even if that tire were to break loose in a low-traction-emergency situation the cruiser would still go where I have it pointed.

Now that I am in RWD locked, oversteer and understeer are easier to reach and less predictable. I no longer have mechanical ABS; both front tires can lock up now, before it would force braking power to the rear prolonging lockup. But a little more driver input and awareness is all it takes to keep things under control.

For DD rigs or first time 80 series owners, the AWD system can't be beat. For trail rigs or those owners who are willing to sacrifice the cushion AWD provides for less wear, more power, lighter steering, and the option of an auto-locker in the front...why not go PT?
 
Back
Top Bottom