fuel injection

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 3, 2009
Threads
45
Messages
2,557
Location
tucson
i don't currently have an fj but want to get one. i am putting together ideas i want it to stay in the "family" and wanted EFI can i bolt a new tacoma motor to the original tranny with a conversion kit or would i have to replace the drive train?:wrench:
 
I'm willing to bet the LC bellhousing will not bolt up to either Tacoma engine. I'm also not aware of an adapter to mate the Tacoma tranny to the LC transfercase (note I have seen it done with a custom one-off adapter). Keep in mind that the rear diff on a LC is offset while the Tacoma is centered. I also think the front drop on the Tacoma is backwards so the Tacoma TC won't work for two reasons.

If you want EFI you will need to either do a 3FE swap, or a TBI on the existing engine. Or, use an engine that adapters are available for (Chevy et al.).
 
Inchworm and Marlin both make adapters from the Tacoma transmissions to the gear driven t-case found in 4Cylinder minitrucks. One could then adapt that GRB to a Land Cruiser t-case using the appropriate adapters. It will make for a long drivetrain, but since the tacoma v6 is considerably shorted from front to back, one could move the whole thing forward.
 
You can get the head/intake/EFI harness/computer from a land cruiser that has a 3Fe engine and put it all on the 2F enging in the FJ-40 (there are some compatibility issues I believe with certain dome pistons)....this is refered to as a 3fe stroker I believe and is a very nice swap. It is involved. I am currently swapping in an entire 3fe as I have the 1F engine to start with instead of a 2f.

The advantage of this is keeping the origional drivetrain and shortblock so there is no need for adaptors.
 
This little project is quite interesting, time consuming to say the least..........:cool:
100222_123418 (Custom).webp
100222_123433 (Custom).webp
100222_123445 (Custom).webp
 
I used to have a '94 4 runner with EFI V-6 could that drive train work if i put in a new rear axle and custom drive shaft in the rear. the tc on that 4runner droped to the right side (passenger):wrench:
 
mtn biker, if you are interested in a TBI conversion for the stock 6 cyl., send me your mailing address for a freebie Fuel Injection Manual before you spend a dime, or make an engine swap choice!!!
 
mtn biker...........

That 3 liter is a BARKING DOG .......

Knowing the history on those things, I wouldn't even consider that .........

The 3.4 really isn't that impressive either.........

If thinking on a transplant , just go for the gusto and jump in with the V8 crowd....
 
i also curently have a sequoia with the 4.7 iforce v-8 would that be a suitable swap out. i want it to be strictly toyota and i don't really want efi for the fuel economy i just don't want to adjusting the carb if i go from az to id or go into the mountains for some wheelin or camping :wrench:
 
mtn biker, if you are interested in a TBI conversion for the stock 6 cyl., send me your mailing address for a freebie Fuel Injection Manual before you spend a dime, or make an engine swap choice!!!
I know that you sent this information before but i don't know where i put everything. any history has passed and i now own a 69 Fj40 with the stock inline 6 "F" motor. i also have a part time job at a certain national parts store where i can get a 20% discount on the Holley sniper but will need to get the adaptor for the intake and air cleaner. What do you recommend.
 
The easiest path by far is to replace carb with a holley sniper tbi if you're just looking for easier starts, slight mileage improvement depending on what you were getting before, and better elavation compensation. If you're looking for massive power gains, v8 swap is common. There are hundreds of posts on this.
 
Back
Top Bottom