Front End Clunk - Steering Stabilizer?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 12, 2011
Threads
18
Messages
94
Location
Columbus, OH
I've been trying to diagnose a front-end clunk for some time now. I've read countless threads on the matter, and still haven't found it. I get under the truck, everything's nice and tight.

Essentially when I'm turning a corner and go over a bump or up an incline, I get a clunk. Happens primarily when I turn left. The clunk only happens when the wheels are turned one right, and I cross center to turn left. Or simply deviate from center and turn left. Once I pass center, it clunks.

The ball joints that connect the steering stabilizer are pretty easy to move, and I can rotate the steering stabilizer with my hand easily. I'm starting to feel like it's the stabilizer clunking when I turn the wheel past center.

Does this make sense, or am I barking up the wrong tree?

Thanks

-MK
 
You're on the right track. You can remove the steering damper and test drive. It doesn't do a whole lot anyway, and even less if it's knackered.

You could also look at the shock absorber bushes, stabiliser/sway bar bushes, swivel hub bearings and their bolts (bolts could be loose).
 
Thanks, didn't realize I could just remove it! At least it would help me narrow it down.

I've put a wrench on just about every bolt on the front end, and all of them are tight.

You need a ball joint separater to get the stabilizer off correct?

-MK
 
Do you feel the clunk with the vehicle not moving but when turning the steering wheel? Do you feel a clunk if someone rocks the vehicle up and down with you sitting inside? How is the steering and tracking?
 
I've been trying to diagnose a front-end clunk for some time now. I've read countless threads on the matter, and still haven't found it. I get under the truck, everything's nice and tight.

Essentially when I'm turning a corner and go over a bump or up an incline, I get a clunk. Happens primarily when I turn left. The clunk only happens when the wheels are turned one right, and I cross center to turn left. Or simply deviate from center and turn left. Once I pass center, it clunks.

Same here and after pulling and shaking on everything, both with the Cruiser on all 4 wheels and having each front wheel jacked up individually, the only possible source I could identify was the left side stabilizer bushing. With the left side jacked up it was showing more distortion than the right side under similar conditions. This past Saturday I swapped out the bushings, easy 1/4 :banana: task. Haven't heard the clunk since, but it's also too early to tell if this has cured the clunk, but I've at least eliminated one possible source.
 
Could also see the other thread that talks about a suspension "clunk", cracked panhard tower or frame section where the steering box bolts to...
 
You're on the right track. You can remove the steering damper and test drive. It doesn't do a whole lot anyway, and even less if it's knackered.

You could also look at the shock absorber bushes, stabiliser/sway bar bushes, swivel hub bearings and their bolts (bolts could be loose).

I just replaced my OME stabilizer with 60K miles with the one from JT's that is the exact same part painted white and half the cost.

By hand, I couldn't tell the difference in compression resistance and thought I'd wasted some coin, but on the rig a very slight tire lateral imbalance shimmy @ 50 mph is gone.

I know people think these things don't perform any function, but the more wear or stress (larger tires) you have, the greater the function.

I doubt that is your clunk, however, as you wouldn't need to hit a bump.
 
I don't need to hit a bump, but it does do it when I hit bumps sometimes.

If I'm driving on a gradual right hand turn (say the steering wheel is maybe 10 degrees off center), and the road curves to the left, it'll clunk when I cross center. But it wont do that if I cross over center to the right.

I also notice it when I pull in my driveway, which has a very small bump as I cross over the apron. The more I drive and think about it, the more I think it's a pop in the steering stabilizer.

I'm going to grab a pickle fork and take the damn thing off to see if that's it or not.

Thanks for the heads up about the budget stabilizer though.

-MK
 
I had an annoying clunk similar to what you describe. It would clunk at slow speed or while stopped when turning the wheel from left to right. I was yanking on everything underneath and couldn't find anything loose. I eventually found a thread on here that said to check torque on various suspension bolts. I did, and found a panhard bolt to be only around 90 ft/lbs; torqued it to specs and the clunk is gone! You might want to check that the bolts are torqued to spec and not just "tight". :)

Mike
 
I know this is an old thread but wanted to confirm and thank madragoran for his comment. The single clunk only happened when I turned hard left at slow speed. was bugging me as i couldn't pinpoint it. Turned out to be the panhard bolt on the passenger side was under torque spec around 90-100ft-lb, torqued to spec (about 127 ft-lb off the top of my head) and the pop has gone away completely. the ds was at spec. been about a month and a half and all good so far! :beer:
 
I'm a newbie and do not have a fraction of the knowledge base that most of the folks I've read on this site do, but I have a similar question. My 1977 FJ55 has been on blocks for about 7 years. I recently started reinvesting in getting her mobile again. I got her running and took her off the blocks to get her ready go to the mechanics. I only drove about 20 feet up my driveway but when I turned the wheel it was a harder pull than I remember and the wheel would clunk as if something was slipping. I'm confident that my mechanic will be able to fix whatever it is, but am wondering if I should attempt the 2 mile drive to his shop or have him trailer it there. I don't want to damage anything. The transmission is also a bit squirly but it has been parked for a long time so I'm hoping as things get lubricated some of these things will fix themselves. This was my first vehicle when I got out of the Army, and though I've had to park it a couple of times due to priorities, I'm determined to get her back on her feet. Looking forward to any and all advice... thanks in advance.
 
Old thread....but it helped me. Want to also thank Madragoran for his comment. Stupid noise was driving crazy. Passenger side track bar bolt was only 90 ft-lbs. Tighted to 130 and all good. This forum rocks!
 
Back
Top Bottom