FOR Suspension Rocks!!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 26, 2008
Threads
3
Messages
16
I've recently installed the FOR GenII suspension on my '97 LX450 and I couldn't be happier.

Here's my deal. I like driving nice vehicles. I also own a 2006 LX470 that is completely stock. After owning the 470 I decided that I wanted a "beater" vehicle that I could take into the mountains on hunting and fishing trips, throw a muddy dog in the back of and run through the rough desert with all of the associated "desert pinstriping". Basically something that I wouldn't give two cares about what happened to it. So I started researching possible vehicles. The LandCruiser and LX450 were no brainers. I ended up with a '97LX450 that had 110k on it and looks like it has never been taken out of the garage or mall parking lot. This thing is perfect. Not a scratch, dent, ding or inch of rust on it. It also has factory lockers. The only sign that anyone has ever driven it is some slight wear on the drivers seat.

Then I started researching this website to find all the cool sh*t I could put on it. Like I said - I like nice vehicles and as long as you're going to have a beater vehicle it might as well look like a kick*ss beater vehicle. I ended putting on an ARB with a Warn winch, sliders, roof rack and a bunch of obnoxious offroad lights. I'm also adding a Slee rear bumper as soon as he has them available again.

Then I started researching lift kits. I had two bipolar requirements for the lift. I wanted it to ride nice and I wanted it to handle just about anything I could throw at it offroad. Much like my requirement in women - good looking and smart and makes a bunch of money. I never said I was realistic, I just have unrealistic standards. So I first looked at the OME stuff. It didn't impress me, but looked like it would work. Then I looked at Slee's stuff - a big improvement over OME but still not the mythical lift I was searching for. Then I heard about the FOR Gen I kit. It seemed much more like what I was looking for. So I called up Frankie and said send one to me. THe only problem was that he didn't have anymore of the GenI kits available. He was a great guy on the phone and seemed to know his stuff. He was down right likeable and the kind of guy I'd like to give my money to. Frankie assured me that he was in the process of creating another kit that was going to be even better than the first one. I asked him when it would be ready - he told me about 6 weeks. Well 6 weeks came and went. I spoke with Frankie a couple more times and he told me about the production delays that he was having but that he'd have them "as soon as they met his standards". Months went by. I was getting to be a bit impatient as I now had this vehicle with all this weight on the factory LX springs and it was beginning to look a bit like a stupid lowrider. I almost bought the Slee kit. Frankie called and said he had the kit ready. I also bought the LandTank plates and Frankies DC front drive shaft. I whipped out my trusty Visa and paid the man. My next problem was finding someone to put the lift kit on for me. I have very little wrenching ability or inclination but I do know a thing or two about making money - so I wanted to pay someone else to do it. I put out an email to the local Arizona Copper State Cruisers website and got a reply from a guy named Eric Murphy. Eric identified himself as the Service Director at Camelback Toyota here in Phoenix and said he could help me with the lift kit. I was a bit skeptical at first. I normally hate dealerships and think they are a ripoff. Eric told me that he has an 80 Series himself and a Toyota Certified Master Technician that can work on the vehicle for me. I still wasn't impresses but he said he could have the lift kit put on "tomorrow" and I was a bit anxious to get it done. I was blown away by the quality of the install and the customer service that came with it. He and his dealership treated me like I owned the place. I was so impressed with working with Eric that I've decided that when I buy a 200 Series that I will drive pass the Toyota dealership in Scottsdale and forgo buying from a friend that owns a Toyota dealership in CA just to be able to buy from Camelback Toyota. I'm not the type to give out many compliments, but I can't say enough about the Service Department at Camelback Toyota. They have earned my business and I will gladly refer them to others.

Anyway, I got the lift kit put on and then added some Nitto Terra Grapplers in 315/75/R16 on factory chrome wheels. I then took it in to have it aligned. The caster came out to a perfect 2.9 and 3.0. It drives straight and has zero vibrations. Oh yea, it also DRIVES AND RIDES LIKE A FRICKIN CHAMP. Holy Sh*t Batman. Slap my grandma and call her nelly. I can't believe how well this thing drives on road. I wouldn't say that it rides like my LX470, but I would say that it is pretty darn close to a 100 Series LC. No kidding. It is that good. It is so much better than it was on the factory springs. It handles perfectly at all speeds and is a true pleasure to drive. I had no idea that a lifted truck with "35 tires could ride so nice. No idea at all.

Now I'm sure there will be some of you that say "what about offroad performance?" Because that is the primary reason for owning these vehicles. My answer is "Come follow me." Very simple and straight forward. I would put the FOR GenII kit up against any other kit out there. Frankly I had no idea that it would perform so well offroad. No idea at all. Now I'm not bashing the offroad performance of Slee or OME. I'm sure they do just fine. But I have a difficult time imagining that they are "better" offroad.

The bottom line is this. The FOR Gen II suspension rides like a dream on the road. The LandTank caster plates and Frankies DC shaft are perfect. The FOR Gen II suspension can handle anything as well as anybody off road. This is the mythical suspension that I was looking for. For anyone who has not ridden in a vehicle like this - don't. You will not be satisfied with anything else, especially your own vehicle, once you have.

By the way, I'm not affiliated with nor have any financial interest in FOR. I've only spoken to him on the phone. He doesn't need my endorsement or my compliments. His suspension says it all for him already.
4-28-09 Misc 044 (2).webp
4-28-09 Misc 051 (2).webp
4-29-09 Misc 048 (2).webp
 
Nice 80. Nice suspension :D

Ride in an OME 80 one day, just so you really know.
 
Here's my F.O.R on 33's.

The on road ride/handling is UNREAL and it seems to wheel pretty good too.
DSC_0237[1].webp
 
Nice beater :D
 
I'm walking in your footsteps! we think alike.

I had the same basic thought process, only I have an 07 100 series as my daily driver. I has the hydraulic suspension and I think the best ride and performance of any stock SUV out there. I just aquired my 80 series LX 450 identical to yours less the lockers with 97,000 milies, original owner, golf villa truck, same color as yours. I have really put some time in readin and talking about all the suspensions because I had the same requirements you just mentioned. Frankie's sounded good but maybe to good to be true. Maybe I should revisit that thought. I had just decided on the OME Heavy front 2.5 with the medium back 2.5 and the lighter shocks they offer. I am going to use the Slee front and rear bumpers. Can I just trade mine in on yours? Any other advice? I am right here in MS next to Frankie, Thanks:clap:
 
Heck of a beater. I just put the OME mediums on my truck only because my stock stuff was original and shot. Cant afford the Frankie's right now and Metaltech had that good sale on OME.

I will have a Frankie's kit by the end of the year. Everthing Ive read has been overwhelmingly positive.

Hey LandCruiser Garrett are you reading this? Get the Frankie's kit.
 
Can you post up some images of a profile of your rig so I can see what F.O.R. looks like on 33s.

Thanks!

-KK

Would like to also see pics with 33's.

I have Toyo's (which are big 35's) on Slee's 4" and it is tight. I am looking at another project with some 33 Toyo's I already have and thought the 3-3.5" FOR II might work perfect, just want to make sure they don't look too small.
 
Does FOR's fit 35s without rubbing? :confused:

Yes, it is designed for 35's. Because the design uses shock mount adapters to go eye to eye to shift suspension travel down vs. increasing the overall compressed and extended length of a stock pin mount shock like OME L, you actually will run 35's with less rubbing than a taller OME lift because the rear travel is not increased simply because you have an inch extra lift. Increasing rear travel means you get more angle into the wheel well and more potential rubbing.

This both improves suspension balance by keeping shock travel tuned to available spring compression/extension as well as ensuring you don't have overly unequal front to rear suspension travel. The first pic here is the only place I ever got big 35's (Trxus and Toyo MT) to rub just barely on the frame (second pic is angle of first pic from the front for perspective, 3rd pic is on 37's). This kit runs 35's clean.


Of course, you can also do 37's with a bit of tuning (you need 1" wheel spacers and perhaps minor triimming) :D
OCG Rock Pile Flex.webp
OCG Front Flex.webp
M Wheeling Full Pic.webp
 
Last edited:
I have a G2 lift kit coming in from Franky as well... Credit card already charged!!!

It was a tossup between Slee and Frankie since the Slee kit gave you so much more for the money... But deciding ride quality would be paramount the Frankie kit was selected.
 
Originally Posted by peepers
do you know how/if the DC shaft differs from Slee's much?


It is entirely Toyota parts.

Nay, not to hijack, but do you know if these are oe Toyota parts, real Koyo joints, or aftermarket joints that are similar to Koyo/Toyota design? Your statement implies parts bought from Toyota.

There is a huge difference between aftermarket parts that are like the Toyota / Koyo design and real Toyota parts. BTDT
 
Back
Top Bottom