Failed CA smog test... help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 6, 2004
Threads
9
Messages
684
Hi guys. It's that time of the year again. I took my truck in for it's smog inspection and failed. I'm hoping someone here can help me diagnose the problem.

'78 FJ40 2F .
Failed the 25mph CO% test..
MAX = 1.39
MEAS. = 2.02

Does this mean I'm running a little rich? What to do to correct this?

Thanks,
Bob
 
High CO is too rich. You can only adjust the carb at idle, beyond that it is internal to the carb. Too rich could also mean not enough air. Check your air filter.
 
Last edited:
yes...Carbon Monoxide. I corrected it above. New spark plug wires if you can believe it does wonders. I ordered the works today because my LV failed emmisions. I'll post the before and after results.

New:

rotor
cap
spark plugs
points
wires
oil
(air cleaner) but it's an oil bath
timing
air fuel ratio
 
Thanks for the help guys. I should have mentioned that my engine has about 2k on it since it was rebuilt . All new wires , rotor, plugs , air cleaner, and to top it off a JimC rebuilt carb. I'll try the oil change and messing with the timing a bit.
Any other thoughts come to mind I would appreciate hearing them.
Thanks, Bob
 
I'm sorta' surprised that they would fail you with that small variance. No doubt you've been more than usually gentle with your engine in consideration of the newness of it but sometimes that can work against you when it regards an emmissions test. I'd bet that if you take a moment just before testing to blow out the buildup of carbon which accumulates in light usage you'll pass with flying colors.
Have the engine at operating temperature, make sure that the choke is fully off, blow it out a bit and keep it at a high idle until you go in.
 
I've dealt with a troublesome '75 FJ40 and Kalifornia smog for many years. Often I was just over the limit just as you are. The things that have helped me the most are:
Check the manifold vacuum. This has been my most common problem. It is easy to develop a rich condition if the engine isn't pulling air properly. Slight leaks here and there, or misadjusted valves can add up. I've rarely failed when I was pulling 17mm Hg.
Set your idle speed a little high. I'm pretty sure the limit for idle measurements on a 2F in California is 1000 rpm. I've failed when idling at 600 but adjusted close to 1000 and passed with no problems.
Do all the tune up stuff as mentioned.

Don't go overboard trying to fix the problem by adjusting the carb. If it is not the source of the problem or you're not confident in what you are doing it is real easy to get everything out of whack. Make sure you've checked everything else first.
 
I just passed smog with my '77 Fj55, similar situation, recently rebuilt engine (last year), rebuilt carb (me). I didn't do much, just made sure the timing was correct. Definitely good to check manifold vacuum, and have it correct. New air filter? Do you have a catalytic converter? (mine doesn't) It may need replacing.

Nial
 
I am trying to get my 60 smogged too. I would look at the carb first. I set my mixture at idle but was told that is just effects the mixure at idle. It has no effect on the mixture while not at idle. That true?

What all your numbers? The CO, NOx, and HC's?

It says a lot when everyone is trying to come up with tricks instead of fixing it right. It is a pain in the arse. :censor:

I have been trying to get mine to pass for months.
 
What does backing off on ign timing affect?

My CO % #'s in Colorado were 0.52 at "idle" (1127 RPM - in think the "idle" cut-off in Colorado is 1200 RPM?) and 0.69 @ 2291 RPM.

I would contact Jim Chenoweth and ask his advice... How long ago did he rebuild the carb?
 
Thanks for all the ideas. This weekend I will be checking the manifold vaccuum ,the timing, idle speed, air cleaner etc. I'm gonna go through all of it.
This truck passed two years ago when I finished restoring it. It was running crappy at the time with the carb rebuilt by me and a headgasket installed backwards ( no top end oil). Now it runs great but won't pass. Oh well, I'll figure it out. Thanks for all the help.

Kevin , here's my numbers:
smog1.webp
smog2.webp
 
PabloCruise said:
What does backing off on ign timing affect?

My CO % #'s in Colorado were 0.52 at "idle" (1127 RPM - in think the "idle" cut-off in Colorado is 1200 RPM?) and 0.69 @ 2291 RPM.

I would contact Jim Chenoweth and ask his advice... How long ago did he rebuild the carb?

I think it was about a year and a half ago that Jim did the carb. Maybe I'll email him and see if he has any ideas. Thanks
 
California Smog Test

I just passed the Smog test for the first time with my '77 FJ40 that originated in Colorado. It failed the first time during the two part inspection. I did three things to make sure I passed the second time.

1. A complete visual inspection of all vacuum, exhaust, and emissions components. I replaced anything that was missing (exhaust heat riser and stack), anything that looked cracked or was excesseively worn.

2. Complete tune-up. Replaced distributor cap, rotor, plugs, fuel filter, air filter, gas cap, and oil change. Adjusted the timing to 7 degrees BTDC, adjusted idle to ~ 650 rpm (per underhood decal), and adjusted the idle mixture to optimum lean condition.

3. Filled the fuel tank up with 91 octane. Burned 1/2 the tank. And made sure the engine was 'hot' when I arrived at the smog station. I was able to time it so that I pulled right into the bay.

It passed with flying colors. I now have California plates. The downside is that since California changed its laws, I will have to do it again in two more years. :rolleyes:
 
Last edited:
I am curious as to how much ethanol we can burn in our Cruisers w/ no ill effects (see https://forum.ih8mud.com/showthread.php?p=408073#post408073 granted, it doesn't look like the thread is getting a lot of traction...).

But a mix of gas and ethanol would produce less emissions. I think I have heard of people running their tanks down and then adding a gallon of white fuel (for camp stoves) before an e-test. But that would be unethical...

Robert, did you tune your carb using the "lean drop"method outlined in the emissions manual?

Any word from Jim C?
 
PabloCruise said:
I am curious as to how much ethanol we can burn in our Cruisers w/ no ill effects (see https://forum.ih8mud.com/showthread.php?p=408073#post408073 granted, it doesn't look like the thread is getting a lot of traction...).

But a mix of gas and ethanol would produce less emissions. I think I have heard of people running their tanks down and then adding a gallon of white fuel (for camp stoves) before an e-test. But that would be unethical...

Robert, did you tune your carb using the "lean drop"method outlined in the emissions manual?

Any word from Jim C?

I haven't tried contacting Jim yet. I thought I would check a few other things before I bothered him. Last year when my secondaries weren't opening i took up his time with carb questions. Turned out the problem wasn't carb related.

I did not tune the carb when i got it back from Jim. I assumed he did that when he tested it. Maybe that's the problem. I think i will email Jim now.
Thanks PabloCruise.
 
California emmssions is a pile of crap intended to generate money for the state! I had to smog my 76 FJ55 before I sold it. It passed emmision but the dude failed it becuase I did not have a fuel spout regulator on the fill pipe. You know the little thing that keeps you from putting leaded gasoline into your unleaded car? Can't even buy leaded gas anymore!!!

The little bitch took my $60 and told me I'd have to retest. I bought a $6 part and banged it into the fuel pipe and had to pay another $70 to get the smog.

Oh yeah, they are strict with the regulations. And I am bitter....I made sure the 40 I replaced teh 55 with was pre-73. California Sucks!!!!

Bitter Colorado Native
 
Back
Top Bottom