ExtremeAire Craftsman Mod

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 15, 2006
Threads
80
Messages
2,843
Location
Lincoln, NE
This was a bit of fun I did over the last couple of weeks while the weather was cold. It is not 80s specific, even though I built it to be used on my 80s.

I decided I wasn't getting near the use I should out of my tool box ExtremeAire compressor. The primary reason was that it wasn't switch regulated.

So, I started pricing switches & tanks & regulators & check valves... Total with shipping was a couple of hundred dollars. I couldn't seem to source a simple check valve or blow off valve locally.

Then I saw this little 3 gallon compressor on sale at Sears for $89 marked down from $129. They're on sale for $99 this weekend, so the price varies depending on what their marketing wants to do with it.

The first thing I did was pull off the compressor part and put it asside into my spare parts for projects stuff. Maybe I'll need a 1hp AC motor someday.

Off with the old, on with the new.

So...
00915310000


+

extremeaire-portable.jpg


=
IMGP1459_small.webp
IMGP1458_small.webp
 
Oh, I also built a manifold system so I can air down / fill up 2 tires at once. With a regulated air compressor with auto on/off I can set the regulator, connect the tires, and go have a sandwich. It works well enough that I'm going to set it up to fill all 4 tires at once.

The compressor turns on at 95PSI and off at 125PSI. Well under the ExtremeAire 150PSI working limit.
 
If you have the toolbox version you'll have everything you need but one piece.

It is a 3/8 compression to 1/4" npt 90* brass fitting. ACE hardware had one for <$5.

If you have the normal version of the compressor, you'll also need 4 short bolts, nuts, lockwashers & 1.5" soft washers. If you look closely, my washers bent a bit as I torqued it down. Its snug on there.

The electrical... I'm not an electrical engineer, so take or leave this as you will.

I measured out the existing plug on the compressor, cut it, put loop type lugs on the ends.

I ran the black/ground to the back of the switch case where the green AC ground was held, then straight out to the plug.

I ran the red + wire in to the DPST switch, ran a jumper from one side to the other on the front & back of the switch making it a SPDT. Then out from there to the plug.

The switch is fully mechanical. I wanted to make sure I made the make/break as easy on it as I could since it is now DC and was built for AC power. I don't think it should care, and is working for me. YMMV on this part, as it is the point where I go into unfamiliar territory.

I like how it turned out. Good luck, and if you need any more pics or whatever, let me know!
 
wow tools
3.4 cfm at 40 psi. that is one hell of a 12v compressor. I wonder what compressor that thing uses. draws 30 amps!

Puma is a prime manufacture, the word is that they make the parts for the extreme air unit, the two units are closely related. The E-Bay unit is the newer casting with bigger head fins, etc, the extreme air pictured above is the older style. A bunch posters over on Pirate run them, most with the tank separated from the pump. The word is that the 30 amps is low, wire for 40+!
 
Oh, I also built a manifold system so I can air down / fill up 2 tires at once. With a regulated air compressor with auto on/off I can set the regulator, connect the tires, and go have a sandwich. It works well enough that I'm going to set it up to fill all 4 tires at once.

Grench,
Do you have pics and details on the manifold set up for filling all 4 tyres at once?

-B-
 
Grench,
Do you have pics and details on the manifold set up for filling all 4 tyres at once?

-B-

I played around with it and decided it wasn't such a hot idea. The end result is that filling 4 33" MTR tires from 30 to 55 psi through a little regulator set at 60 psi takes a long long time.

Running the regulator at 100 psi and manually filling two tires at once is quite doable.
 
I'm wondering what size AC/DC Inverter you're using for the Craftsman unit - that is unless it's a 12V compressor...the Sears down the street from me is out of stock on them - so I'm having to wait -

Figuring a CO2 tank may be a better solution for me in my FJ40 - just due to the tank size....not much space to stuff the tank & the compressor...Think I'm going back to the drawing boards.

Anyone have pics of theirs installed??

Sears does have some sweet deals from time to time!
 
Last edited:
its good to see some long term feedback for a compressor, looks like almost four years and running strong?

I would like to upgrade my little compressor one day, although Ian's left a york amongst other stuff sitting in my garage for a dangerously long amount of time, maybe ill try that instead.
 
I'm wondering what size AC/DC Inverter you're using for the Craftsman unit - that is unless it's a 12V compressor...the Sears down the street from me is out of stock on them - so I'm having to wait -

Figuring a CO2 tank may be a better solution for me in my FJ40 - just due to the tank size....not much space to stuff the tank & the compressor...Think I'm going back to the drawing boards.

Anyone have pics of theirs installed??

Sears does have some sweet deals from time to time!

Please re-read the original post and look at the before and after pictures.

I took the Craftsman compressor off and tossed it in the scrap heap. I put an ExtremeAir 12VDC compressor on it utilizing the pressure switch, blow off valve, line cooler, tank, etc...

It works great.
 
To bring this thread back from the dead...

I just picked up a Central Pneumatic 3 gallon compressor at Harbor freight for $40 with coupon:

http://www.harborfreight.com/1-3-hp-3-gallon-100-psi-oilless-air-compressor-97080.html

I will be dropping my ExtremeAire on top of this. A cheap way to get a tank, 2 gauges, a regulator, a blow-off valve and a cut off switch.

My ultimate goal is to have a larger tank permanently mounted under the FJ60 with this being the air supply. I'll work out some quick connect system for the compressor mount, the air out to the truck's tank and power to the compressor.

I want to be able to use the compressor/tank mounted in the truck or pulled out as a true portable. (I have 3 cruisers at the moment and wanted to be able to have air in whichever one I was using at the time.)

mark

IMG_20130622_211103_272.webp
 
Very nice. The only piece I didn't have between the ExtremeAir toolbox kit and the Craftsman tank & equipment was a reducer coupling that I picked up at my local Ace hardware for cheap.

Isn't it weird/sad that it's cheaper to buy a whole compressor + tank and chuck the compressor than it is to buy a tank, gauges, pressure relief and switch?
 
In retrospect I probably should have just bought a Puma but I do think this turned out ok... Gray box contains a 70a relay with a separate 1a fuse for the switch wires. There is a 50a fuse in the jumper cables I am using for battery power...

IMG_20130815_112953_635.webp


IMG_20130815_113009_961.webp


IMG_20130815_112911_461.webp
 
Nicely done!

I did not put any fuses on mine - instead I have a power distribution panel in the back PS quarter storage box with a 40A circuit for the compressor line. For mobile use - straight to the battery. I figure that in that scenario I'm there to pull the plug if it starts to smoke or such.
 
I've never seen you wear suspenders, that would be avatar worthy!
 
Back
Top Bottom