emmissions help in CO !!!

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 16, 2003
Threads
47
Messages
498
Location
Aurora, CO
Hey folks,

Been a darn long time since I've posted. I'll try to keep it brief. Trying my best to pass the CO emissions with my 74 de-smogged fj40. Failed two times now...first time was total failure, second time wasn't a total failure, but still failed.

truck has an *ich* Holley carb from PO. I've rejetted it for higher altitude, put a full tank of E85 in it (to keep the emissions down), installed petronix ignition, new plugs, new oil and oil filter, couple cans of seafoam, fuel injector cleaner.

I'm failing my Carbon Monoxide test. My value at idle is 6ish, passing is 3ish. any suggestions beyond getting rid of the holley? Or does anyone have a good line on a factory carb?

thks!

Later

Kumar
 
It is running rich at idle. If it is only rich at idle, try adjusting the idle mixture. If it is rich at all speeds, it could be a clogged air filter, stuck choke or the main jets are too big.

I'm not 100% sure on how to adjust the idle mixture. I adjusted two screws, left and right in relation to the float boal, so that my idle was as high as I could get it (oddly, i could only get it to 700 rpm and not higher). Heard that running at 950 rpm would normally pass the idle test. I'm having a heckuva time finding online docs on tuning the carb.

k
 
Use a vacuum gauge. Adjust to get the highest vacuum reading possible.
From a California smog site
Carbon Monoxide (CO)*
CO is created when gasoline is not completely burned. High CO ( running rich ).

A list of common causes of CO related smog check failure:

1. Timing is not a big factor in CO production but check it anyway. Everything helps.

2. On older Carbureted vehicles you can have problems like a partially stuck choke plate.This is the moving steel plate on the top of your carburetor.

3. A leaking power valve on your carburetor can cause high CO and Smog Check failure.

4. A faulty carburetor can cause high CO and Smog Check failure.

5. A dirty air filter can cause high CO.

6. A common cause for high CO is a faulty Oxygen Sensor. This sensor tells the computer how to fine tune the air fuel ratio.

7. Other sensors like the M.A.P.sensor , C.T.S. sensor or the Air flow meter can also effect the CO level.

8. A faulty air injection system can cause high CO. This is the Smog pump and related components.

9. A faulty Catalytic Converter can cause high CO and Smog Check failure.

10. If your car has been running rich ( high CO ) you should change your oil after you get it repaired. When you have rich condition all the fuel cannot be burned, you start to saturate the motor oil with CO and HC. This in itself can also cause a rich condition.
 
Are you failing Co at idle or at 2500 RPM?

Do you have a vac guage? What is it reading at idle? Does the needle bounce?

You are right, you will have an easier time at a higher idle. Figure that carb out...

Just got in from "figuring that carb out". Found a few things of interest on how to adjust it on the web...turns out I need to adjust BOTH idle/air needles the same amount. So what I did was close them BOTH down (totally lean), then back them off about 1/4 turn. From there I had a really low idle, so I took the curb idle screw (towards the rear of the carb near the throttle), and screwed it in until I reached 950 rpm. Took her out for a spin and she run pretty well...especially considering I have e85 in it and I'm at about 5500 ft in altitude :) A lot of the "stink" is now gone...so tomorrow I give her another run at the emissions joint.

thanks!

Kumar
 
Are you failing Co at idle or at 2500 RPM?

Do you have a vac guage? What is it reading at idle? Does the needle bounce?

You are right, you will have an easier time at a higher idle. Figure that carb out...

oh forgot to mention...I'm using a tach gauge to check the rpm, not a vacuum gaugue. It stays pretty consant for where I set the rpm...but it does sometimes go up/down. The only vaccuum line I have is from the distro to the carb IIRC. The entire truck was de-smogged and de-hosed by PO.

later,
k
 
I had a really low idle, so I took the carb idle screw (towards the rear of the carb near the throttle), and screwed it in until I reached 950 rpm.


I don't know about CO, but that would fail in CA because it isn't idling if it isn't the factory spec idle speed (550 RPM). It is running on the main nozzles.

There is something wrong if it won't idle at normal speed. Open the idle mix screws about 3 turns and then adjust the idle speed to 650. Then turn the idle speed mix until the speed drops to 550. Then look down the bore of the carb and see if it is pulling fuel out of the main nozzles at idle (it shouldn't) If it won't run w/o pulling fuel from the main nozzles, you may have a vacuum leak or a plugged idle circuit and somebody has messed with the carb as a band aid to get it to run.
 
I don't know about CO, but that would fail in CA because it isn't idling if it isn't the factory spec idle speed (550 RPM). It is running on the main nozzles.

There is something wrong if it won't idle at normal speed. Open the idle mix screws about 3 turns and then adjust the idle speed to 650. Then turn the idle speed mix until the speed drops to 550. Then look down the bore of the carb and see if it is pulling fuel out of the main nozzles at idle (it shouldn't) If it won't run w/o pulling fuel from the main nozzles, you may have a vacuum leak or a plugged idle circuit and somebody has messed with the carb as a band aid to get it to run.

I'll probably do a fine tune after the emissions pass..bringing everything back to spec. For right now I heard a "trick" was to increase the idle. Once I pass the emissions once (by the way, they didn't even notice I was missing the smog pump), I will get collector plates and then never again do I do emissions for the 40, while in CO :)
 
kumar,
welcome to colorado!

who's doing you e-test?
jim

Hey Jim. Can you PM me your number.

From what I understand I have to get aircarecolorado to do my testing...is there somewhere else?

Kumar
 
You have to smog a '74 in CO? What the hell?

I have a 75 ;) From what I understand, if your truck comes with factory smog equipment, then it must test with the factory stuff. but from what I also understand, these emissions places are big drive through's with 'non-technical' folks running a recipe card to get folks through :)

later,

k
 
I have a 75 ;) From what I understand, if your truck comes with factory smog equipment, then it must test with the factory stuff. but from what I also understand, these emissions places are big drive through's with 'non-technical' folks running a recipe card to get folks through :)

later,

k

older than 81 can go to any garage that can do emissions. some of the smaller shops are a bit more "lenient" ;) once you get a pass, put collector plates on it so you don't have to do emissions again.
 
older than 81 can go to any garage that can do emissions. some of the smaller shops are a bit more "lenient" ;) once you get a pass, put collector plates on it so you don't have to do emissions again.

Thanks, That's the info I needed. I new 25 years was an important date but didnt know how it fit in.

Looking at possibly importing an HJ47. 81 or older:cool:
 
Hi,

You might want to try one of these from Eastood Co. I have one and tune my motorcycle at idle regularly. They are very good at sniffing the CO in your exhaust.

I hope this helps.

Doug:cool:
 
older than 81 can go to any garage that can do emissions. some of the smaller shops are a bit more "lenient" ;) once you get a pass, put collector plates on it so you don't have to do emissions again.

Yeah, what Ige said. Once you pass and get collector plates you never have to check it again. You also get to register it for 5 years at a time. Any vehicle that is 25 years old can get collector plates.
 
I went to another air care colorado location than before...this was after I re-adjusted the idle/air mixture and idle. Not sure if their equipment was better or if my adjustments worked ;)

wow, what a huge difference. I not only passed, but I passed with flying colors!!!

@idle (926 rpm for before and 1350 rpm for after ;)
HC % before -> 910
HC % after -> 138

CO% before -> 8.87
CO% after -> .18

@ 2500 rpm
HC % before -> 1396.4
HC % after -> 128.6

CO% before -> 4.7
CO% after -> .16

She's all registered for 5 years now :)

now I need to bring her back into specs.

thks!

kumar
 
Back
Top Bottom