Diff bolts

How do I remove fill plug without destroying it?

  • I have 24mm 6 point socket

    Votes: 7 100.0%
  • It started to round so I stopped. Help

    Votes: 0 0.0%

  • Total voters
    7

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Morgan is on the intel....

True preload may not be exact but many here including myself have had good luck with unstaking the nut. Counting turns to get it off precisely. Replace pinion seal and add nut back to exact number of turns plus 1/8 revolution.

Pinion yes. ~1hr

Axle as well but an all day job so maybe best to wait for the spring temps. Keep knuckles topped off till you can address.
Can be done in 5-6 hrs. First time is nice to allot 8 or a weekend so you can attack over two days. ive never had the luxury of a garage either and have rebuilt 4 or 5 now.
 
Is this a driveway job? B/c I have no garage. Also how long of a job approx? I like the idea of doing the job just a little intimidated and short on workspace. Thanks for tip
Last weekend I stripped both of my axles, removed borh 3rds and stripped the 3rds down. I have a garage, but all that gives you is protection from the elements...not sure what the weather is like where you are, but in NJ its between 5 and 10 degrees for the past few weeks. If the weather isn't too cold then you can do this on your driveway.... I have done plenty of work on my driveway including knuckles and xfer case work

If you are just replacing the pinion seal the easy way, figure 10 mins to get the drive shaft nuts & bolts out, 10 mins to get the pinion nut and flange off, 10 mins to remove the seal and tap the new seal in place. 15 mins to put everything back together. Total of 45-60 mins on the conservative end.

If you need to R&R the knuckles figure on spending the whole day to do both sides.

I can completely tear down a front axles in 2 hours, but I have done it more times than I can count, the first time takes a lot longer.

I think you shoukd go for it, if you get stuck get back on mud and ask for guidance.
 
I have another diff related question- the front pinion leaks. Should I spend 300 to get that fixed or just keep filling the diff (assuming I get the fill bolt out)

How bad is the leak? If it is just a wet spot that is enough to collect dust on the diff, Don't worry about it, just stay on top of the maintenance/inspections and top it off when needed. If it is dripping on the ground pretty obviously, it still is not very much grease that is leaking out. Keep an eye on it and decide how soon you want to deal with the seal. A friend of mine lives in Sierra Vista and has had good luck with the Toyota dealership there doing good work for a fair price.
 
Let start by saying that you guys are amazing! The info and input have really got me excited about tinkering with the fj80 again (I was a bit demoralized yesterday). Also, the knuckles have a grease fitting? Thought I saw one but wasn't sure b/c of crust.
 
the knuckles have a port on top that you can open to check the moly level..you can use it to squirt more in there in a pinch, but if its low, you would be better off rebuilding anyway.
 
the knuckles have a port on top that you can open to check the moly level..you can use it to squirt more in there in a pinch, but if its low, you would be better off rebuilding anyway.

Most knuckles have a 12 mm square plug high and forward of center on the knuckle housing. Kinda hard to see in there, but it should nbe 2/3 - 3/4 full of moly based grease. If your not sure, just pump in half a tube of grease into each side. Drive it for a week or so and recheck.
 
Chisel and hammer or grind a socket flat so it doesn't have the rounded lip at the head to help it seat on the bolt.

Also, every crusier (or solid-axle mini truck/4runner) owner should rebuild their knuckles at least once as a right of passage. Extra points for doing it in a parking lot or on the trail.
 
Went and bought an impact wrench and ground off the chamber on a 24mm socket and the fill bolt came out like magic! So glad I let 'Ol Blue sit till I did that! Front axle was almost empty, took 3 full quarts! Rear diff took just over a quart. I am super grateful for the tip about the port on top of the knuckles, each knuckle took a full tube of moly lube. I bought the earthquake 20v impact from harbor freight- 1100ft. lbs. Of torque. I was determined to get those bolts today, now I'm thinking it's probably overkill and I might overtighten or destroy fasteners with that beast. Any thoughts on a good torque rating for an impact to use on the cruiser? Thanks again for all the good advice! Thanks to you guys my axles will live to see another day.
 
Oh yeah, any thoughts on what oil to use in the diffs and t-case? Manual says 75 w-90 but gallons of 80 w-90 are cheaper at my local autozone. Also what about adding Lucas or something like that?
 
I just refilled my rear diff, t-case and front diff with 80w-90 Super Tech from our local WalMart. Prob get flamed for that but I figure clean oil and the correct qty is way more important than the 75w vs 80w debate ?
 
Went and bought an impact wrench and ground off the chamber on a 24mm socket and the fill bolt came out like magic! So glad I let 'Ol Blue sit till I did that! Front axle was almost empty, took 3 full quarts! Rear diff took just over a quart. I am super grateful for the tip about the port on top of the knuckles, each knuckle took a full tube of moly lube. I bought the earthquake 20v impact from harbor freight- 1100ft. lbs. Of torque. I was determined to get those bolts today, now I'm thinking it's probably overkill and I might overtighten or destroy fasteners with that beast. Any thoughts on a good torque rating for an impact to use on the cruiser? Thanks again for all the good advice! Thanks to you guys my axles will live to see another day.

Use the impact to remove bolts, never to tighten. Always use a torque wrench to put stuff back together unless you've got a good sense of what you're doing with hand tools.
 
Back
Top Bottom