Cylinder Head Cracked

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 19, 2005
Threads
28
Messages
70
So, just heard from machine shop that my 1980 2F cylinder head has cracks in from the valve seat traveling into the head. At this point they said the cracks are not leaking, but could at any point. I told the machine shop to deck the damn thing, put new valve seals (not seats) on it, and I will bolt it back on.

SOR wants 590 for a reconditioned head, plus shipping, plus time to get the thing. Anyone get reconditioned heads from them?

I am in Austin, TX and don't know of any local shop that would have a used head (I don't want to go to Wimberly 4wheel...). Anyone know of any good sources here in Austin.

Thanks
 
I would not spend the time installing a cylinder head with known cracks....only to be required to do the same job again.



Find a good head and do it right the first time.


Good luck!


-Steve
 
Change it out now, you can find a new head for 100 to 150, rebuild of the head is 150 bucks then your good to go, scrap the SBC, Larry
 
Change it out now, you can find a new head for 100 to 150, rebuild of the head is 150 bucks then your good to go, scrap the SBC, Larry



Larry-


Let me know where you are getting GOOD(useable, no cracks) late modle 2F cylinder heads for 100.00.....'cuz I will take four of 'em. ;)



:beer:
 
Change it out now, you can find a new head for 100 to 150, rebuild of the head is 150 bucks then your good to go, scrap the SBC, Larry

Now that my sanity is back I am not going to bolt the old head back on. Trouble now is finding a head. I would love to get one for 1 to 1.5 bills and have it machined. But I just can't find one right now, and even if I do I still run the risk that it has a crack. If it is not a head I can get locally I could lose another week just to find out the used head I just bought is cracked.

It is looking like I will order the SOR rebuilt head tomorrow....unless someone has a known 'good' head they want to sell :)
 
So, just heard from machine shop that my 1980 2F cylinder head has cracks in from the valve seat traveling into the head. At this point they said the cracks are not leaking, but could at any point. I told the machine shop to deck the damn thing, put new valve seals (not seats) on it, and I will bolt it back on.

SOR wants 590 for a reconditioned head, plus shipping, plus time to get the thing. Anyone get reconditioned heads from them?

I am in Austin, TX and don't know of any local shop that would have a used head (I don't want to go to Wimberly 4wheel...). Anyone know of any good sources here in Austin.

Thanks

Wimberley 4X4 is not selling any heads at this time.......
 
cylinder head

I ran into the same problem on a 1981 I restored. Did not want to put out the money for a used head not knowing the condition. To have one shipped alone is around $100 I bit the bullet and bought form SOR. Sticker shock for sure. I now know if you find a good one keep it around just in case. I do have one from a 1981 but am reluctant to sell it. If you run into a dead end let me know and I will think about it.

Regards...
 
I ran into the same problem on a 1981 I restored. Did not want to put out the money for a used head not knowing the condition. To have one shipped alone is around $100 I bit the bullet and bought form SOR. Sticker shock for sure. I now know if you find a good one keep it around just in case. I do have one from a 1981 but am reluctant to sell it. If you run into a dead end let me know and I will think about it.

Regards...

Thanks for the offer. SOR has them in stock so I don't think I will run into any dead ends....but sticker shock for sure :eek:
 
Tim Hill has a number of heads. You would have to call him and find out which versions. His cell number is 520-240-3757. He lives in Avra Valley which is NW of Tucson, AZ. I was just out there to buy a rebuilt two stage brake booster he had in stock and I saw a number of heads. Tim is a straight up guy. He is as honest as they come. If you saw the extent of FJ40 hardware at his property, most of you would find drool running down the side of your mouth.
 
Just gave him a call. Nice guy. For everyone's info he sells completely stripped heads that have been magnafluxed for $225, and 'straight off the engine' heads that have not been checked out also for $225. He did not have any rebuilt heads in stock.

At that price + machine work I am still leaning towards SOR.
 
Back
Top Bottom