clutch fan suck

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 6, 2014
Threads
59
Messages
363
Location
Colorado
Website
cannabisforcolorado.com
Clutch fan is stuck cant remove it from the pully.
Tried hitting it with a rubber mallet, hitting it with a hammer lightly, now im trying to hammer a wedge in. wont move.
all 4 nuts removed.
Taking everything off to change water pump, radiator, hoses, clutch on fan.
20191118_145853.webp
 
isn't the pulley held on behind the clutch fan?
 
The pulley should fall right off with the fan. But its clearly seized behind the fan. I'm having brain farts today. lol
 
Penetrating oil and a little judiciously applied heat should do it.

I have some WD40 on it now. Ill throw some heat on it tomorrow.
Thanks
 
You might try getting a pry bar behind it. Or using a stud remover and backing the studs out. Might want to replace the studs anyway
 
If it's that stuck...I wouldn't try to wedge anything behind it. You'll just scar/damage the pulley or clutch base. Instead of trying to break it free in the axial direction, use a blunt tipped punch and sharply rap the base of the clutch, turn 90° and repeat, turn 90° and repeat. That way it should break free in the 'shear' direction, much easier to do.
 
Mine was like that when I first tried to remove it.


Blunt punch; tap tap tap, turn, tap, tap, tap, turn, tap, tap, tap, turn,...........
 
could "gently" tapping the side of the pulley on the perimeter with a mallet help?
 
Put it all back together with the bells on nice and tight. Then remove the fan clutch nuts and the tension of the belts will kick the pulley and fan loose.
 
Put it all back together with the bells on nice and tight. Then remove the fan clutch nuts and the tension of the belts will kick the pulley and fan loose.

Yep, right into his radiator. ;)

I know...the belts and studs are 'supposed' to hold it all in place, but 'Murphey' is still alive and well.

A controlled approach might be the better way.
 
Whats happened is moisture has got in between the female fan clutch hub and the male water pump pilot shaft causing corrosion to form locking both items together. Once you get this apart and go to put it all back together, first clean off all the corrosion. Then put a THIN coating of grease or never seize on the water pump pilot shaft, that should prevent this from happening again.
 
Yep, right into his radiator. ;)

I know...the belts and studs are 'supposed' to hold it all in place, but 'Murphey' is still alive and well.

A controlled approach might be the better way.
I've done it numerous times and never had it go into my radiator. I have thought about putting a piece of cardboard in front of the fan so I didn't hit it when removing it. Otherwise I've never had a problem doing it that way.
 
His radiator is coming out anyway so I'd do that first then get mid evil with this SOB! On another thread he mentioned his radiator has cracked open.
 
His radiator is coming out anyway so I'd do that first then get mid evil with this SOB! On another thread he mentioned his radiator has cracked open.

Well....that takes care of any radiator worries then. I still wouldn't go to the trouble of putting it all back together when rapping on the clutch base will free it as well. Doesn't really matter to me how it gets it done, I don't have any skin in the game, just offering up a suggestion that has worked for thousands of mechanics nearly forever.

Hope the OP gets it sorted out. No fun sometimes hitting these stopping points.
 
Put nuts back a few threads (keeps pulley from flying off) and use a air chisel with a blunt end. The hammering effect will make short work of it. I do this when removing pulley from a crank dampener on my Cummins isx. Once again make sure it’s a dull chisel.
 
Back
Top Bottom