Check out this thermo rad cap

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Oct 5, 2003
Threads
298
Messages
3,662
Location
Saratoga Lake, NY
Check this out. Not too bad for $18.00
Helmer parts sells to the forklift market. The bottom of the page has Toyota numbers, Toyota sells forklifts too.
Anyone.........Beno :D..... have a cross reference to the oem cap. Wonder if one of these would fit?


400500<br>RADIATOR CAP / THERMOMETER

400500-2.webp
 
That's actually pretty cool. I want one!
 
Kinda cool actually, especially for those of us with ODB1 (ie: no way to get a good temperature that I'm aware of).

Koso gauge on the block discharge pipe and analog gauge in the block drain plug has been working great for me.

I've honestly never seen my rig go over 190 on the discharge side, and 185 from the block drain since my rebuild. And those were on the hot days 108 ambient temp

That is a cool cap though, I'd buy one right now if it had a second needle showing system pressure in psi
 
Isn't the rad cap an engineered pressure release point for the cooling system - ie. 13 psi? Does this cap have a similar pressure release point?
I think getting a new OEM rad cap is a good move when buying any used vehicle, especially our touchy Cruisers with known cooling issues. Having a gauge on the cap is coolish, but better than a new OEM cap? I'm not so sure.
 
How about one that shows the pressure instead? I think that would be a little more useful than another gauge to keep looking at, which won't match the computer number, so people will freak.
 
Isn't the rad cap an engineered pressure release point for the cooling system - ie. 13 psi? Does this cap have a similar pressure release point?
I think getting a new OEM rad cap is a good move when buying any used vehicle, especially our touchy Cruisers with known cooling issues. Having a gauge on the cap is coolish, but better than a new OEM cap? I'm not so sure.

It says .9 on the nub which I'm assuming is BAR. That is roughly 13 psi
 
Doesn't the koso gauge work on the block temperature and not the coolant liquid itself?

No

The sensing unit (the tip) is surrounded by flowing coolant . It's very responsive
 
Isn't the rad cap an engineered pressure release point for the cooling system - ie. 13 psi? Does this cap have a similar pressure release point?
I think getting a new OEM rad cap is a good move when buying any used vehicle, especially our touchy Cruisers with known cooling issues. Having a gauge on the cap is coolish, but better than a new OEM cap? I'm not so sure.
AKA 0.9 bar which this cap is rated for. It's just a radiator cap which either holds the right pressure or doesn't.
 
How about one that shows the pressure instead? I think that would be a little more useful than another gauge to keep looking at, which won't match the computer number, so people will freak.

I would hope someone wanting a temp sensor at the rad cap would be smart enough to know it will read a different thep than the OEM sending unit.
 
I would hope someone wanting a temp sensor at the rad cap would be smart enough to know it will read a different thep than the OEM sending unit.

No one would know unless it's OBD2 with a scanner plugged in ;)
 
@Dave 2000 you put a loss of coolant pressure warning buzzer on yours right?

No, it is loss of water level, with LED and buzzer, Cartek Coolant Level Alarm | Demon Tweeks

I used a custom dash insert for the led and a seperate buzzer.

There was a pressure sensor mentioned on here awhile back but needs pressure to be built before indicating a problem. That's ok as long as the water has not leaked out overnight for example, no water and you start up drive and realise the pressure warning light has not gone out after 'x' time, unsure how long your expected to wait though before taking action?

Regards

Dave
 
Last edited:
Back
Top Bottom