check engine light on

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 21, 2015
Threads
1
Messages
6
Location
Bordeaux France
hi guys, I m Matthieu from France and I have a problem on My 1997 FZJ80,

the check engine light is on, when I do the schunt on the diagnostic plug between TE1 and E1 the light give me the code 22.

I know this is the coolant sensor ECT on the engine, and I've change this by a Toyota genuine parts but the light is always here.

when I start my 80, the light is off, the engine become warmer and if I don't drive there is no light, even if the engine turn before 30minutes, but if I begane to drive slowly at 30mph the light is on!

the 80 drive well, no problems, no powerless,

I have the supercharger TRD but the problem became after 1500miles.

Here in France, nobody know the petrol engine only diesel, that s why I m here, I need your help.

thanks
 
Bonjour Matthieu.
Savez-vous si votre camion est OBD2?
Avez-vous un port de diagnostic par le genou gauche du conducteur?

Good morning Matthieu.
Do you know if your truck is OBD2?
Do you have a diagnostic port by the driver's left knee?
 
Jonheld if i remember right EOBD2 was not required on gasoline engines until Jan 1 2001 in Europe
 
Hello, no it s not obd2, this is the old plug and nobody has a diagnostic tool for this one, and I search on the internet where I can buy a diagnostic tool with the program and the old plug.

But if somebody here has good information on the fuel injection that could help me.
 
Dumartin, the old Snap On MT2500 scanner might work with your trucks OBD1 system. As a matter of fact, i own, and use that scanner on my 1994 land cruiser that's OBD1. You can find Snap On MT2500 scanners for sale on EBay, for cheap, the thing is, you would need to make sure you got the correct software and Toyota #1 plug for it. They sell the software for the MT2500 on EBay too, If you have any questions about this scanner just PM me.
515d4tDkd+L._SS500_.jpg
 
Last edited:
On the US spec vehicles I believe there are two coolant temperature sensors, one for the ECM the other for the dash gauge. You may not have replaced the correct one.

There is a scan tool that connects to older Toyota vehicles. Currently they are listed as out of stock as a new version is being built. It interfaces to an Android App named TOYODB1.
OBD1READ 22P
 
Last edited:
Ok, thanks for the name of the diag and your answer, I replace the good sensor, There is 2 cable on the connector, and my plug is under the engine hood on the Right side.

I disconnected the efi fuse for30 min and test drive, same résults, light on at 30mph

Something could be on the same circuit for turning the light on with the code 22?
 
Dumartin, it sounds like your system is a OBD1 system, that uses the 17 pin connector on the firewall. If you get a MT2500 scanner with the Snap On Asian primary software cartridge through 2000 / troubleshooter software cartridge through 1999. With the MT2500 hooked up to your engine with the Toyota 17 pin connector you'll be able to read all your codes. Plus the scanner has complete information on every code for your truck stored inside it and it's all displayed on your scanner.
s-l1600.jpg

s-l1600.jpg
 
There is two sensors which one did you replace, the one more then likely that is throwing the code is above your oil filter just to the right. Post up which one you changed
 
I change the good one on the right of the oil filter with 2cable connector, the other is for my gauge and my gauge works good, I dont understand why with a new sensor the Check light come back
 
Back
Top Bottom