catalytic converter question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 14, 2008
Threads
31
Messages
151
Location
Johnson City, TN
I have a 1997 LX450 with 145k. What are the advantages and disadvantages of having/not having catalytic converters sans emmission issues? I have access to the tools I need to remove the cats if I want to. Would one have to do anything more to the LX other than chopping them out and fabbing and welding pipe in? Is there any way to tell if my current cats are clogged and in need of replacement? I searched "catalytic converter and catalytic converter replacement" and found a few threads on 100 and 60 series but did not find conclusive answers that applied to me.

Many thanks for your input,
Katie
 
I have a 1997 LX450 with 145k. What are the advantages and disadvantages of having/not having catalytic converters sans emmission issues? I have access to the tools I need to remove the cats if I want to. Would one have to do anything more to the LX other than chopping them out and fabbing and welding pipe in? Is there any way to tell if my current cats are clogged and in need of replacement? I searched "catalytic converter and catalytic converter replacement" and found a few threads on 100 and 60 series but did not find conclusive answers that applied to me.

Many thanks for your input,
Katie
you can punch out the material in the cats instead of chopping the cats out, use a resperator and a long pipe and hammer and drive the pipe through a few times till al the material is out, it takes a little effort, i dont know how it will run after though matbe someone else can chime in
 
Your 97's OBDII system will throw fits if you remove the converters, since you have O2 sensors after the cats. To avoid this you can buy an O2 sensor eliminator (google is your friend) but I don't have any experience with these to comment about. YMMV
 
We are making a high flow y-pipe/cat section and muffler if you're just wanting to replace the entire thing. And doing it this way, you'll free up more HP/TQ and still keep the ECU happy with the O2 sensor readings since there's a cat in the system.

If you're just wanting to chop our your cats and call it a day, it's not hard to do, just replace them with pipe, or gut the cats as mentioned above, and then follow by addressing the O2 sensor issue.
 
We are making a high flow y-pipe/cat section and muffler if you're just wanting to replace the entire thing. And doing it this way, you'll free up more HP/TQ and still keep the ECU happy with the O2 sensor readings since there's a cat in the system.

Go with an oversized high flow cat. Much more flow than OEM, and will keep the ECU happy.


If you're just wanting to chop our your cats and call it a day, it's not hard to do, just replace them with pipe, or gut the cats as mentioned above, and then follow by addressing the O2 sensor issue.

The rear O2 sensor is actually used to adjust the long term fuel trim. By putting a sensor eliminator on there, you are actually eliminating a value that the ECU uses to adjust how much fuel is being used.

It's not worth doing it. :meh:
 
Chopping the cats, while possible with 02 trickery, is irresponsible in my opinion, unnecessary for a fact, and eliminates much of the OBD-II's diagnostic duty which will ultimately have you chasing problems with performance, emissions and economy down the road. Vehicles that come from the factory without cats have different ECU's to avoid all these issues. My suggestion is simply put in a high-flow / high-performance cat such as the one I opted for in the link that's below and then perhaps use pipe that baktasht is making in his shop. That way you'll have all the advantages of having the cat/s and none of the disadvantages. HTH. :cheers:

https://forum.ih8mud.com/80-series-tech/239588-catalytic-converter-option-forced-induction-rigs.html
 
Back
Top Bottom