Cat blanks/"test" pipes

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 3, 2006
Threads
259
Messages
1,935
Location
Fort Apache: Victoria
I'm trying to get some "test pipes" done locally, but nobody can seem to match the flanges.

Anyone here ever make straight pipe sections to replace the cats?
 
Yes...
ByPass.webp
 
That's the stuff. Did you make your own? Where'd you find the flanges?
 
cut the flanges off your old Cats

There's the rub. I need to keep the cats intact in case I ever get a roadside inspection and receive an order to re-install them.
 
I'm trying to get some "test pipes" done locally, but nobody can seem to match the flanges.

Anyone here ever make straight pipe sections to replace the cats?

How much power do you actually gain by taking out the cats? Is the increased emmisions/possible ticket actually worth it?
 
How much power do you actually gain by taking out the cats? Is the increased emmisions/possible ticket actually worth it?

yes....











no prolly not but its the "cool factor" that counts and it will change the exhaust tone a lil too.

my 60 has no cat.
in 08 it becomes a clasic and will be saftey only so i dont need it anymore.
 
How much power do you actually gain by taking out the cats? Is the increased emmisions/possible ticket actually worth it?

There's no annual inspection here, only occasional roadside inspections for vehicles that attract attention (ie +6" lift, poor visual condition, no muffler, no mud-flaps, etc). The odds of a near-stock, late model Cruiser in good overall condition getting a VI are very slight here. However, in the event I did get stopped, I'd want to have the cats intact so I could reinstall them in the event of an inspection order.

As for performance, I doubt it's that big a deal with/without. My problem with the cats is the way they reduce ground clearance.
 
There's no annual inspection here, only occasional roadside inspections for vehicles that attract attention (ie +6" lift, poor visual condition, no muffler, no mud-flaps, etc). The odds of a near-stock, late model Cruiser in good overall condition getting a VI are very slight here. However, in the event I did get stopped, I'd want to have the cats intact so I could reinstall them in the event of an inspection order.

As for performance, I doubt it's that big a deal with/without. My problem with the cats is the way they reduce ground clearance.

Just now getting into the 80's and I did notice that the cats will be rock bait. Are there any smaller cats or a way to reroute so they are out of the way?

We only have smog insp in Cali every 2 years for older vehicles but I would like to retain the cats just for the emmisions. Our air in parts of Socal is already bad enough.
 
I'm trying to get some "test pipes" done locally, but nobody can seem to match the flanges.

Anyone here ever make straight pipe sections to replace the cats?

I have heard of people just knocking out the internal guts
of a cat ie: using some long metal bar, screwdriver, even a power drill with a long anything on the end to break up the guts;
then put them back in place; so externally, they look stock.

Not recommending it, what with the ozone and all, but a thought.

g
 
I have heard of people just knocking out the internal guts
of a cat ie: using some long metal bar, screwdriver, even a power drill with a long anything on the end to break up the guts;
then put them back in place; so externally, they look stock.

Not recommending it, what with the ozone and all, but a thought.

g

Just one more time for the record; it's not the performance (or lack thereof) that interests me, it's the gain in clearance. The cats hang too low. And as I don't need them where I live, I wan to replace them with some low-tech, low profile pipe.
 
Just one more time for the record; it's not the performance (or lack thereof) that interests me, it's the gain in clearance. The cats hang too low. And as I don't need them where I live, I wan to replace them with some low-tech, low profile pipe.

Why not do the cut-and-turn?
 

Many people here there aren't happy with the position of the cats, like you are, simply have them cut loose and welded back in a flatter position. They "cut" and "turn" them.

May depend on year tho, I didn't see one in your sig. Some (I think 95+) are more in line, my 94's are side by side as pictured. I assume if it is a big deal they could be repositioned slightly.

:confused:

(Don't listen to me, I never post in tech:D)
 
Many people here there aren't happy with the position of the cats, like you are, simply have them cut loose and welded back in a flatter position. They "cut" and "turn" them.

May depend on year tho, I didn't see one in your sig. Some (I think 95+) are more in line, my 94's are side by side as pictured. I assume if it is a big deal they could be repositioned slightly.

:confused:

(Don't listen to me, I never post in tech:D)

ah, I see.

Mine's a '94, so no OBDII issues. I figure just take 'em out and avoid the heat issues, etc. Plus mine are kind of rusty (they look original); I'm not sure they would survive much modification. Plus I'm one of those people who think the whole cats thing is the ultimate in splitting hairs - "let's see, I drive a three-ton SUV all day, everyday... I better make sure the cats are working properly so I don't ruin the environment!"
 
ah, I see.

Mine's a '94, so no OBDII issues. I figure just take 'em out and avoid the heat issues, etc. Plus mine are kind of rusty (they look original); I'm not sure they would survive much modification. Plus I'm one of those people who think the whole cats thing is the ultimate in splitting hairs - "let's see, I drive a three-ton SUV all day, everyday... I better make sure the cats are working properly so I don't ruin the environment!"

Won't work on yours or mine anyway...no room to turn them over on their side, since they are side by side...
 
ah, I see.

- "let's see, I drive a three-ton SUV all day, everyday... I better make sure the cats are working properly so I don't ruin the environment!"

True...I see your point. You are up in BC and the air is cleaner there anyway. Down here is Socal every little bit helps and I will probably only put about 5-8k a year on mine.
 
How much power do you actually gain by taking out the cats? Is the increased emmisions/possible ticket actually worth it?

My entire exhaust was pretty rusty. so chopping them off was no big deal. I did notice an increase in power, mainly on the top end.

We have annual emission inspections here in Phoenix, so eventually I'll pop a set of cats back on. I haven't looked for the flanges, but they can be easily made from 3/8's steel if you have a plasma cutter or torch.
 
Back
Top Bottom